background image

 

 

 

BP301                                                             

www.bpfasteners.com

 

Page 2 

 

WARNING! 

PRIOR TO OPERATING THE BP301 TOOL, PLEASE STUDY THIS MANUAL CAREFULLY AND DEVELOP A 
THOROUGH UNDERSTANDING OF THE CONTENTS. PROPER TRAINING ACCORDING TO THE CURRENT ANSI 
STANDARD A 10.3, SAFETY REQUIREMENTS FOR POWDER ACTUATED FASTENING SYSTEMS MUST BE 
COMPLETED AND A BLUE POINT FASTENERS QUALIFIED OPERATOR CARD MUST BE OBTAINED PRIOR TO 
OPERATION OF THE TOOL. STATE, LOCAL, OR OTHER REGULATIONS SHOULD ALSO BE FOLLOWED. LAWS, 
REGUATIONS, AND STANDARDS REGARDING THE USE OF POWDER ACTUATED TOOLS MAY PERIODICALLY BE 
REVISED WITHOUT NOTICE. ANY SUCH REVISIONS MAY CHANGE THE SAFETY AND OPERATING PROCEDURES 
DESCRIBED IN THIS MANUAL. BLUE POINT FASTENERS, INC. IS NOT RESPONSIBLE FOR ANY SUCH REVISIONS 
WHICH OCCUR AFTER PUBLICATION OF THIS MANUAL. IT IS THE RESPONSIBILITY OF THE USER TO MAINTAIN 
ALL KNOWLEDGE OF THE LAWS, REGULATIONS, AND STANDARDS THAT APPLY TO THE POWDER ACTUATED 
TOOLS. 

 

DANGER! TO AVOID SERIOUS INJURY OR DEATH:

 

NEVER PLACE YOUR HAND AT THE END OF THE FASTENER GUIDE OF THE BP301 TOOL. 
OPERATORS AND BYSTANDERS AROUND THE TOOL BEING USED MUST USE EYE AND EAR PROTECTION. 
ALWAYS ASSUME THAT THE TOOL IS LOADED WITH A LOAD. NEVER PLACE YOUR FINGERS ON THE TRIGGER OF 
THE LOADED OR UNLOADED TOOL UNTIL THE TOOL FASTENER GUIDE IS AGAINST THE WORK BASE AND YOU 
ARE READY TO DO A FASTENING. IF THE TOOL ACCIDENTALLY SHOOTS HIS/HER HAND OR ANY PART OF THE 
BODY, THE PISTON CAN ENTER THE BODY AND CAUSE SERIOUS INJURY OR DEATH. 
IT IS VERY IMPORTANT THAT THE OPERATOR OF THIS BP35 TOOL READS AND UNDERSTANDS THE FULL 
MANUAL OF THE TOOL AND COMPLETED THE OPERATORS EXAM WITH A 100% GRADE. THE WARRANTY DOES 
NOT APPLY UNTIL BLUE POINT FASTENERS, INC. RECEIVES A COPY OF OPERATORS EXAM AND A COPY OF YOUR 
RECEIPT WHEN THE TOOL WAS PURCHASED. 
 
 

WARRANTY 

All warranties or products described herein, express or implied, including the warranties of merchantability or 
fitness for a particular purpose, are specifically excluded, with the following exceptions: Blue Point Fasteners 
will repair or replace, at its option, any tool, part or element holding that, within 90 days after the sale. If Blue 
Point is found to be responsible for a defective part in material or workmanship, excluding normal wear. THIS 
IS THE ONLY WARRANTY AND REMEDY BLUE POINT HAS AVAILABLE AND IS IN NO EVENT FOR ANY DIRECT, 
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR ANY OTHER DAMAGES, is available. 

 
 
 

 
 
 
 

Summary of Contents for BP301

















Reviews: