background image

chipping tube for chipping by the rotating blade. 
2. Some side shoots and branches may have to be trimmed from the main stalk before 
chipping. 
3. Shorts stubs of branches may be pushed through the chipper section with next branch, 
never use hand. 
4. Last branch is pushed inside of the tube by some tools like wood stick. Never try by hand. 
5. Never push the small branches by hand, use wood stick instead. 
6. When feeding branches, be certain that thicker branches should be pushed more slowly 
than thin ones. A technique and understanding will be acquired to successfully shred very 
soon.  
7. Do not allow an accumulation of processed material to build up under discharge of the 
shredder-chipper as this can result in clogging. Use wood tools to clear the build up.   
8. Do not put your face close to the feed hopper, which may result in injury.   
9. Do not stand in front of discharge opening and never attempt to open the outlet of 
discharge while machine is on operation. 
10. Set back the cover to the side tube once finishing chipping. 
ii. Leaves and Grass Shredding 
1. Leaves and short stalk (bean plants), cobs, sod and similar material should be fed into the 
hopper and chipped in 16 interlaced chipping lots. 
2. Do not open the plastic cover when adding more material. 
3. The leaves and similar material is a little hard to go into the hopper. Use a wood stick to 
push them in instead of by hand or other metal bars. 
4. Keep your face and body away from the feed hopper to avoid being struck by any material 
that may bounce back. 
5. The discharge area is easily clogged if the material remains more water or sticky. Always 
stop engine before clearing build-up with wood tools. Never use hand or foot. 
6. Never attempt to clear an accumulation of processed material when engine is still on work. 
7. Perhaps you get other pretty plants in your garden and the material will be processed to be 
organic fertilizer as follows. 

Put the discharge towards a wall, large board or other obstruction. Opening the discharge 

door and remove the screen to allow the processed material pile up. With a garden spade feed 
this material into the shredder until it reaches the consistency you want. 

Keep pet, bystander away from the discharge area while the machine is on operation. Set 

the screen back to the place and close the discharge door when shredding is finished.

 

VII. Sharpen the blade 

Cutting blade is made of special material and the blade is very sharp after heat treatment. It 
may be dull after used for some time. 
Judgment for dull blade: when the chipping sound become very ponderous and the belt 
always skids while it is not loose, or feeding speed gets slow, please remove the blade and 
check if it is dull. 
1. Turn off the engine before remove the blade. 

● 

Remove the board covering the blade. 

● 

Open the small outlet of the discharge. 

● 

Remove the discharge screen. 

2. Wearing safety gloves, turn the blade tray to a proper position. 
3. Remove the location screw on the two pieces of blade.

 

Summary of Contents for CS-65












Reviews: