background image

Loading Dock Equipment Manufacturers

A Product Section of Material Handling Industry of America,

A Division of Material Handling Industry

8720 Red Oak Blvd., Suite 201, Charlotte, NC, 

28217-3992

Telephone: (704) 676-1190 Fax: (704) 676-1199

ALSO MEMBERS OF :

American National Standards Institute (ANSI)

1430 Broadway

New York, NY 10018

(212) 642-4900

LOADING DOCK EQUIPMENT MANUFACTURERS

2.                                                INTRODUCTION

The following is a quick reference to important procedures that must be followed while using the Dock Leveler. It is not 

intended to cover, or suggest that it does cover, all procedures necessary to ensure safe operation. All operators should 

be aware of and abide by all workplace safety regulations applicable to the operation of the Dock Leveler system. These 

laws and regulations include but are not limited to:

•   The Occupational Safety and Health Act (USA)

•   Occupational Safety and Health Acts for Individual States (USA)

•   Canadian Material Handling Regulations

For additional information on these regulations as well as industry standards that may apply to this product, please 

contact:

The manufacturer assumes no liability for damage or injury to persons or property which occur as a result of defects or 

faults in or incorrect use of the Dock Leveler. The manufacturer also assumes no liability for lost profits, operating 

downtimes, or similar indirect losses incurred by the purchaser. Injury to third parties, irrespective of its nature, is not 

subject to compensation.

The manufacturer reserves the right to make changes at any time to the modules, components, and accessories, 

concurrent with its continuing product development program. Specifications, operating instructions, and illustrations 

included in this manual are subject to change without notice. Please contact manufacturer for the latest information.

MANUFACTURER’S NOTE

The Dock Leveler has been carefully inspected and tested at the manufacturer’s plant prior to shipment, but should be 

checked upon receipt for transport damage. Any observed transport damage is to be listed on the signed copy of the 

freight document. Notify the freight forwarder of any damage WITHIN 48 HOURS.

2.2                                        EXCLUSION OF LIABILITY

2.3                                        MANUFACTURER’S NOTE

Thank you for purchasing Blue Giant products. We appreciate your business, and are confident that our product will 

serve you for many years to come. In the event that you experience a problem with our product, our Warranty Center 

is here to support the Blue Giant Product(s) that you have purchased. 

To validate warranty on recently purchased equipment, please complete and submit your information with our on-line 

Warranty Registration at www.BlueGiant.com. 

For more information about Blue Giant's Warranty Support, please contact your local Blue Giant Equipment dealer, 

representative or authorized partner near you. You may also visit www.BlueGiant.com or phone 1-905-457-3900.

* Note that failure to validate warranty at the time of receipt can seriously affect the outcome of any claim.

2.1                                       WARRANTY INFORMATION

U-SERIES AIRBAG DOCK LEVELER with SINGLE PUSH BUTTON CONTROLS

 
2

Summary of Contents for U-Series

























Reviews: