background image

BREWING COFFEE

CAUTION:  

BURN HAzARD 

Exposed surfaces of the 

brewer, brew chamber and 

decanter may be HOT to 

the touch, and can cause     

serious burns.

CAUTION:  

BURN HAzARD 

To avoid splashing or   

overflowing hot liquids,

ALWAYS place an empty 

decanter under the brew 

chamber before starting 

the brew cycle.  Failure to 

comply can cause serious 

burns. 

CAUTION:  

BURN HAzARD 

After a brew cycle, brew 

chamber contents are 

HOT.  Remove the brew 

chamber and dispose of 

used grounds with care.  

Failure to comply can 

cause serious burns. 

IMPORTANT:

Brew delay feature 

prevents multiple brews.   

A second brew cannot 

be started until a fixed 

time after the end of the        

previous brew.

Pressing the BREW button 

during the delay time will 

cause a beep to sound and 

the SERVICE FAUCET 

TANK light to flash.

A.  PREPARATION

 

Place one (1) genuine Bloomfield

 

paper filter in the brew chamber.

 

Add a pre-measured amount of

 

fresh coffee grounds.

 

Gently shake the brew chamber to

 

level the bed of grounds.  Slide the 

 

brew chamber into place under the 

 

brew head.

B.  AUTOMATIC OPERATION

BE sure “READY - COFFEE SYSTEM” light is lit.
Place the appropriate EMPTY decanter in place under the brew     

chamber on the bottom warmer.
Press BOTTOM warmer switch to ON to energize the bottom  

warmer.
Press the “BREW” button.  The solenoid will open for an amount of  

time determined by the timer setting, admitting a measured quantity  

of water into the tank.
Inlet water will displace a like amount of heated water from the     

coffee brew water tank.  The hot water will be forced into the brew  

head where it will spray over the bed of grounds.  Freshly brewed  

coffee will begin to fill the container under the brew chamber.  
When the flow and all dripping stops, the coffee is ready to serve.

Discard the contents of the brew chamber and rinse it in a sink.   

At conclusion of brew delay, the brewer is ready for another brew  

cycle.

C.   WARMERS

 

Press TOP FRONT warmer switch or TOP REAR warmer  

switch to ON.  Set the decanter of freshly brewer coffee on the     

appropriate warmer.

 

IMPORTANT:

  DO NOT leave an empty decanter on an energized  

warmer.  DO NOT allow a decanter to boil dry.

Fig. 7 Brew Chamber

8

915  2M-Z15131 Owners Manual for 8783MCD  

915  2M-Z15131 Owners Manual for 8783MCD 

 

IL1605

Summary of Contents for 8783D3FM

























Reviews: