background image

SERVICING INSTRUCTIONS (continued)

TEMPERATURE ADjUSTMENT

Thermostat control may be accessed by removing either of the 

two button plugs on the right side of the brewer.  Front control is 

COFFEE BREW temperature; rear control is FAUCET WATER 

temperature.

Place empty container under brew chamber or faucet.  Energize 

brewer and allow unit to heat.   When READY indicator lights, 

press BREW button, or raise faucet lever.  Read temperature of 

water entering container.
Adjust WATER TEMP shaft on thermostat;  clockwise increases 

temperature.  Refer to Table 1 below for proper brewing              

temperature based on altitude.

Upon completion reinstall button plug(s).

Fig. 10  Adjusting Brew Temperature

CAUTION:  

SHOCk HAzARD 

These procedures involve 

exposed electrical circuits.  

These procedures are to be  

performed by qualified technical 

personnel only.

Adjustments to be performed by 

qualified technician only.

NOTE: 

Optimum coffee brewing     

temperature is 195ºF to 205ºF 

(90ºC to 96ºC).

Thermostat should be adjusted 

to a maximum temperature of 

203ºF (95ºC). 

NOTE:  Water temperature 

adjustments may be made by 

removing the appropriate button 

plug from the side of the brewer, 

then turning the thermostat 

adjustment shaft.  Check water 

temperature at the brew head 

for coffee, or at the faucet for 

hot water.  Because of losses 

in the connecting piping, the 

procedure at left provides a 

more accurate gauge of the   

actual tank temperature.

IMPORTANT:

A mechanical thermostat will 

maintain temperature within 

±5ºF (±3ºC).
To prevent boiling water in 

the brewer, controller should 

be adjusted to a maximum 

temperature of 10ºF(6ºC) 

less than the local boiling 

temperature, or 202ºF (94ºc), 

whichever is less. 

NOTE:

1/8 turn  = approx 10ºF (5.5ºC)

Table 1    Boiling Temperature by Altitude

12

ELEVATION (feet above seal level)

0

50

0

1,0

00

1,5

00

2,0

00

2,5

00

3,0

00

3,5

00

4,0

00

4,5

00

5,0

00

5,5

00

6,0

00

6,5

00

TE

M

P.

 (º

F)

195

200

205

210

190

IDEAL

BREWING

TEMPERATURE

MAXIMUM 

TEMPERATURE

SETTING

BOILING

POINT OF

WATER

ELEVATION (meters above seal level)

0

15

0

30

0

45

0

60

0

75

0

90

0

1.0

50

1.2

00

1.3

50

1.5

00

1.6

50

1.8

00

1.9

50

TE

M

P.

 (º

C

)

91

94

97

100

88

IDEAL

BREWING

TEMPERATURE

RANGE

MAXIMUM 

TEMPERATURE

SETTING

BOILING

POINT OF

WATER

IL1606

915  2M-Z15131 Owners Manual for 8783MCD  

Summary of Contents for 8783D3FM

























Reviews: