Blomberg 8978983800 Service Manual Download Page 65 | Manualshive

Page: 65 / 70

background image

BWOS 30100 SERVICE MANUAL

65

7.17 POWER BOARD SUBSTITUTION

1.  Disconnect the power supply cord and remove the Oven from the cabinet.
2.  Remove the upper cover.
3.  Remove the screws connecting the power board before disconnecting the cables.
4.  Replace the new power board using the spacers.
5.  Connect the cable following the electric diagram.

6. IT IS VERY IMPORTANT TO CONNECT THE CABLES IN THE RIGHT POSITION.

7.  The connections must not be loose.
8.  Reconnect the power supply cord before installing the Oven and check all functions.
9.  Disconnect the power supply cord and reinstall the Oven into the cabinet.
10. Reconnect the power supply cord after installing.
11. Run the Oven and check all functions.

«
...
63
64
65
66
67
...
»

Summary of Contents for 8978983800







































































Reviews:

No comments

Related manuals for 8978983800

Brand: Oster Pages: 28

Brand: Palsonic Pages: 36

Brand: Inoxtrend Pages: 21

Brand: Toastmaster Pages: 12

B87VS38 0B Series

Brand: NEFF Pages: 60

Brand: Smeg Pages: 43

Brand: NEFF Pages: 116

Brand: DAEWOO ELECTRONICS Pages: 34

Brand: NEFF Pages: 32

Brand: Midea Pages: 14

Brand: Hansa Pages: 56

Brand: NEFF Pages: 32

Brand: IKEA Pages: 12

Brand: Oursson Pages: 72

Brand: DAEWOO ELECTRONICS Pages: 44

Brand: Lamona Pages: 24

Brand: Samsung Pages: 132

Brand: Hanseatic Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands