background image

 

CAUTION: Low or high voltage can detrimentally affect the refrigeration unit. 

 

All units should be plugged into a grounded and properly-sized electrical outlet with 

      appropriate overcurrent protection. Please refer to the electrical requirement on the 

nameplate. 

If you do not have the right outlet have a certified

 

electrician   

install the correct power source. 

 

 

 

To minimize shock and fire hazards, be sure not to overload outlet.                 
Please designate one outlet for your unit., make sure that the unit is properly 
grounded.

 

 

  Please make sure that your unit has its own dedicated outlet. Do not use an extension 

cord. 

 

 

 

 

 

 

  When the unit is not in use for a long period of time, please unplug the unit from the 

outlet.

 

  After unplugging the unit, wait at least 10 minutes before re-plugging it. Failure to do so 

could cause damage to the compressor.

 

  Do not attempt to alter or tamper with the electrical cord. 

 

 

OPERATION                                                                           

 

 

GENERAL USE OF THE CABINET   
 

Blast chiller & freezer quickly reduce the core temperature of the products, whether they are 
cooked or fresh, conserving their fresh texture, hygiene and quality, whilst reducing the risk of 
bacteria generating. 
The traditional method of storing cooked food has always been to leave it to cool naturally until it 
reaches a suitable temperature to store in the refrigerator. 
During the period when the core temperature falls from +65ºC and +10ºC, the food will lose a lot 
of its natural characteristics, such as moisture, consistency, aroma and color. These blast chillers 

Summary of Contents for BCF20


















Reviews: