Configuration Mode (ConF)
70
S1A28692 03/2010
Parameters described in this page can be accessed by:
Macro Configuration
Example of total return to factory settings
!
[Config. Source]
(
FCSI
)
is set to
[Macro-Conf]
(
InI
)
!
[PARAMETER GROUP LIST]
(
FrY-
)
is set to
[All]
(
ALL
)
!
[Goto FACTORY SETTINGS]
(
GFS
)
is set to
[Yes]
(
YES
)
Code
Name / Description
Factory setting
COnF
[1.3 CONFIGURATION]
(continued)
CFG
[Macro configuration]
[Start/Stop]
(
StS
)
g
DANGER
UNINTENDED EQUIPMENT OPERATION
Check that the selected macro configuration is compatible with the wiring diagram used.
Failure to follow these instructions will result in death or serious injury.
StS
HdG
HSt
GEn
PId
nEt
[Start/Stop]
(
StS
)
: Start/stop
[M. handling]
(
HdG
)
: Handling
[Hoisting]
(
HSt
)
: Hoisting
[Gen. Use]
(
GEn
)
: General use
[PID regul.]
(
PId
)
: PID regulation
[Network C.]
(
nEt
)
: Communication bus
g
These parameters only appear if the corresponding function has been selected in another menu. When the parameters can
also be accessed and adjusted from within the configuration menu for the corresponding function, their description is detailed
in these menus, on the pages indicated, to aid programming.
To change the assignment of this parameter, press the ENT key for 2 s.
2 s
2 s
DRI- > CONF
Summary of Contents for ER51
