Blease Sirius 1000 Manual Download Page 35 | Manualshive

Page: 35 / 107

Blease Sirius 1000 Manual Download Page 35

34

First Line and Planned Maintenance Manual

Frontline Sirius®

Slide onto mounting rods

To Scavenging

To CGO

To ventilator

Patient Circuit

TUBING ONLY APPLIES
TO SIRIUS 1000 & 2000.

2.7 Absorber Pre-Use Check

WARNING: Do not use a faulty absorber - injury to the patient may result. Call

an authorised service engineer or return the unit to the supplier.

      1.   Carry out a careful visual inspection of the absorber.
      2.   Ensure the absorbent canisters are full and installed. Ensure that all canister seals are
           present and are correctly installed. (See Fig. 5).
      3.   Undo the two valve covers and check that both the inspiratory and expiratory valve discs
           are clean and free to operate. Check the valve seats for chips, damage, etc. Replace the
           discs and covers.
      4.   Ensure that the bypass control is in the ABSORBER ON position.
      5.   Ensure that the oxygen sensor port either has a sensor fitted or that the blanking plug is
           fitted.
      6.   Ensure all tubing is correctly and securely installed.

Figure 4 Attaching Absorber Tubing

2. User Pre Use Testing

«
...
33
34
35
36
37
...
»

Summary of Contents for Sirius 1000












































































































Reviews:

No comments