Blaze King APEX CBT Operation & Installation Manual Download

Page: 2 / 40

OM-APEX E V1.06

November 19, 2012

Page 2

APEX CBT

Table of Contents

INTRODUCTION

_____________________________________________________________ 3

SPECIFICATIONS

_____________________________________________________________ 4

APPLIANCE DIMENSIONS

______________________________________________________ 5

PRODUCT INFORMATION

_____________________________________________________ 6

CERTIFICATION LABEL

________________________________________________________ 7

SAFETY PRECAUTIONS

________________________________________________________ 8

INSTALLATION INSTRUCTIONS

_________________________________________________ 9

INSTALLATION INSTRUCTIONS - Venting

_________________________________________ 15

INSTALLATION INSTRUCTIONS - Combination APEX-Electric

_________________________ 19

INSTALLATION INSTRUCTIONS - Combination APEX-Gas/Oil

_________________________ 21

INSTALLATION INSTRUCTIONS - Wood only

_______________________________________ 23

VB1000 BLOWER

_____________________________________________________________ 24

OPERATING INSTRUCTIONS

___________________________________________________ 25

BYPASS

............................................................................................................................................ 25

CATALYTIC MONITOR (THERMOMETER)

................................................................................. 25

FUEL

................................................................................................................................................ 25

AIR SETTINGS

................................................................................................................................ 26

THERMOSTATS

.............................................................................................................................. 26

FAN OPERATION

............................................................................................................................ 27

LIGHTING THE FIRE

..................................................................................................................... 27

OPERATION DURING POWER FAILURE CONDITIONS

............................................................. 28

MAINTENANCE

______________________________________________________________ 29

ASHES

.............................................................................................................................................. 29

CATALYTIC COMBUSTOR REPLACEMENT

................................................................................ 29

GASKET INSPECTION

.................................................................................................................... 30

LOADING DOOR GASKET REPLACEMENT

................................................................................. 30

BYPASS DOOR GASKET REPLACEMENT

..................................................................................... 31

ADJUSTING BYPASS HANDLE

...................................................................................................... 31

CREOSOTE

__________________________________________________________________ 32

BRICK LAYOUT

______________________________________________________________ 33

REPLACEMENT PARTS

________________________________________________________ 34

WARRANTY

_________________________________________________________________ 36

NOTES

______________________________________________________________________ 40

Manufactured By

Valley Comfort Systems Inc.

1290 Commercial Way

Penticton, BC V2A 3H5

CANADA

Phone: 250-493-7444

Fax: 250-493-5833

Blaze King Industries

146 A Street

Walla Walla, WA 99362

U.S.A.

Phone: (509) 522-2730

Fax: (509) 522-9803

Summary of Contents for APEX CBT









































Search results

Summary of Contents for APEX CBT

Reviews:

Related manuals for APEX CBT

Brands by name

Popular brands

Blaze King APEX CBT, Operation & Installation Manual

Search results

Summary of Contents for APEX CBT

Reviews:

Related manuals for APEX CBT

Brands by name

Popular brands