BLAUBERG Ventilatoren VENTO Eco A50-4 Pro1 User Manual Download Page 17

www.blaubergventilatoren.de

vento eco

17

STORAGE AND TRANSPORTATION REGULATIONS

•  Store the unit in the manufacturer’s original packaging box in a dry closed ventilated premise with temperature range 

from +5 ˚C to +40 ˚C and relative humidity up to 70 %.

•  Storage environment must not contain aggressive vapors and chemical mixtures provoking corrosion, insulation, and sealing 

deformation.

•  Use suitable hoist machinery for handling and storage operations to prevent possible damage to the unit.
•  Follow the handling requirements applicable for the particular type of cargo.
•  The unit can be carried in the original packaging by any mode of transport provided proper protection against precipitation and 

mechanical damage. The unit must be transported only in the working position.

•  Avoid sharp blows, scratches, or rough handling during loading and unloading.
•  Prior to the initial power-up after transportation at low temperatures, allow the unit to warm up at operating temperature for at least 

3-4 hours.

TROUBLES AND TROUBLESHOOTING

Trouble

Possible reasons

Troubleshooting

The fan does not move up 
during start-up of the unit. 
The control panel displays 
no information and does not 
respond to button pressing.

No power supply.

Contact a qualified electrician to check power 
supply and troubleshoot a connection error if 
required.

The alarm indicator 

 is 

displayed on the control panel.

Motor jam because of impeller clogging.

Turn the ventilator off. Troubleshoot the impeller 
clogging. Restart the ventilator.

Communication loss in the cable connection 
between the fan motor and control panel. 

Turn the ventilator off.
Contact the Seller for further information.

Tripping of the circuit breaker 
during start-up of the 
ventilator.

Overcurrent as a result of short circuit in the 
electric circuit.

Turn the ventilator off.
Contact the Seller for further information.

Low air flow.

Low set fan speed.

Set higher speed.

The filter is clogged, the fan or the regenerator 
is contaminated.

Clean or replace the filter.
Clean the fan and the regenerator.

High noise, vibration.

The impeller is contaminated.

Clean the impeller.

TROUBLESHOOTING

Summary of Contents for VENTO Eco A50-4 Pro1





















Reviews: