background image

INTRODUCTION 

 

The Minibike Elite 14 WRS is designed and built for use on a paved closed 
circuit track.  The track should be clean and without obstacles of any kind.  
Qualified adults and younger persons can drive the minibike. Children can 
drive the minibike only under the supervision of a responsible adult person. 
The minibike is constructed especially for racing competitions on special 
racing tracks. Minibike Blata should not be used during winter season and 
under bad weather conditions. Usage under these conditions leads to 
abnormal mechanical wear and corrosion of most minibike parts - especially 
those directly exposed to climatic influences. Beside that, riding under these 
conditions increase the risk of injury or health damage. 
The minibike uses a single-cylinder two-stroke, Gasoline combustion engine, 
and has an air filter and exhaust silencer. Transfer of power to the rear wheel is 
through a drive chain.  The the overall drive ratio to the rear wheel can be 
changed by the replacement of chain sprockets. The front and rear wheel is 
equipped with disk brakes. The rear brake is controlled with the left lever and 
the front brake is controlled with the right lever on the handlebars. 
 

BASIC TECHNICAL DATA  

 
ENGINE: BLATA…………………………….………………………TWO-STROKE 
 NUMBER 

OF 

CYLINDERS ............................................................... 1 

                     CYLINDER CAPACITY         …………………………….. .........39,8 cc 
 

ENGINE COOLING SYSTEM………………………..LIQUID COOLED 

 POWER 

OUTPUT ............................................ 8,6 kW at 11 300 rpm 

 

TORQUE ………………………………..............6,95 Nm at 11 000 rpm 

 CARBURETOR ..............................................PHVA 14 DELL’ ORTO 
 

FUEL ADMISION …………REED VALVE DIRECT TO CRANKCASE 

 IGNITION............................................................... CONTACT - LESS
 SPARK 

PLUG……………………....................................  NGK B9EGV 

 STARTING .......................................... HAND PULL TYPE, MANUAL 
 CLUTCH.............................................. CENTRIFUGAL AUTOMATIC 
FRAME: WELDED 

...........................................HIGH STRESS STEEL TUBES 

BRAKES: FRONT 

WHEEL ......................................................... DISC BRAKES 

 REAR 

WHEEL.............................................................DISC BRAKES 

WHEELS: FRONT ........................................... OF 

LIGHT ALLOY 2,1”x 6,5”- 99 

 REAR ........................................... OF 

LIGHT ALLOY 2,1”x 6,5”- 130 

TIRE: FRONT .....................................................................SIZE 90/65 - 6,5” 
 REAR .........................................................110/50 - 6,5”, 90/65 - 6,5” 
FUEL: 

.........MIXTURE OF PETROL 95 OR HIGHER 2 STROKE 
SYNTHETIC OIL MIXING RATIO (after break in period)........  33 : 1 

 TANK 

CAPACITY .....................................................................1 Litre 

SPEED:  

WITH THE INSTALLED RATIO: .................... up to 50mph( 80km/h) 

UNLOADED WEIGHT: .................................................................. (50,6lbs.) 23 kg 
CARRYING CAPACITY:.................................................................(240lbs) 110 kg 
BASIC DIMENSIONS: 
 LENGTH.................................................................... 37,7 “ (960 mm) 
 WIDTH............................................................................ 20” (500mm) 
 HEIGHT ...................................................................... 21,2” (540 mm) 

 

Summary of Contents for Minibike Elite 14 WRS

























Reviews: