background image

 

 

 

1. Introduction 

 
It is important that all persons who are working or maintaining this machine read the manual carefully and 
understand it fully.  
Keep this manual near to the machine, so it can always be consulted. 
Only authorized and trained personnel may operate this machine. 
 
 

2. Machine description 

 
The Blastrac dust collector BDC-99 can only be used for dry cleaning.  
It should 

only be

 used for removing 

not

-

inflammable dust or substances

The BDC-99 must 

not

 be used for 

carcinogenic or asbestos substances

 
 
The machine is designed for usage in conditions according to classification 

(see below). 

 
 
 

Classification acc. standard EN 60335-2-69 – Annexe AA 

Class 

Designation 

(Low risk ) for separating dust with an exposure 

limit value of over 1 mg/m3, depending on the 

volume occupied. 

M    

(BDC-99) 

(Medium risk) for separating dust with an 

exposure limit value of over 0,1 mg/m3, 

depending on the volume occupied. 

H  

 

(High risk) for separating al dust with an 

exposure limit value lower than 0,1 mg/m3, 

depending on the volume occupied. Including 

carcinogenic and pathogenic dusts. 

 
 

Dust emissions into the environment 

Class 

Value of performance 

Retains at least 99,1 % of particles measuring ≥ 3 μm 

Retains at least 99,9 % of particles measuring ≥ 3 μm 

Class H13 HEPA filter in accordance with EN1822 

 
 

 
Application 

 
The BDC-99 is especially designed to be used in combination with Blastrac machines. 
And can also be used with every other type of machine. 
Contact Blastrac B.V. for the correct execution and combinations. 
 
 
 
 
 

Summary of Contents for BDC-99

















Reviews: