ENGLISH
GB
ROTOR BLADE POSITION
In the event that a rotor blade requires replacing, ensure the drone is
switched OFF (O). It is important to install rotor blades in the correct
position. Drone may not perform correctly if the spare rotor blades
are not installed correctly. Refer to page 3 for correct position.
A. BATTERY INSTALLATION
1.
Remove the screw from the battery cover at the back of the
handset.
2.
Place 3x AAA batteries in the battery compartment,
as per the polarity shown inside.
3.
Replace the battery cover and
tighten the screw. Batteries to be replaced by an adult. New non-
rechargeable alkaline batteries are recommended for optimum use
and maximum performance. Drone LED lights will flash when low
battery.
B. CHARGING FROM USB
The drone is supplied with an initial charge allowing you to start
using straight away. To prevent overcharging the battery please
ensure the battery is fully discharged before recharging.
1.
Ensure
the drone is switched OFF (O).
2.
Plug the USB into a computer/
USB port.
3. DO NOT plug the USB charger into an AC Adapter.
4.
Insert the USB cable pin connector in to the drone battery
port, located on the back of the drone. Be careful not to force the
connectors as it may cause damage. The RED LED on the USB will
turn on, indicating that the drone is charging.
5.
The drone is
charged after approximately 60 minutes. The RED LED on the USB
will go out, indicating that the drone battery is fully charged.
6.
Remove the USB cable pin connector from the drone battery port
once the charging is complete. DO NOT OVERCHARGE. Flight time
5-6 minutes.
C. SYNCHRONISE - IMPORTANT!
1.
Ensure ‘Control Stick A’ is positioned down fully before
synchronising the handset and drone.
2.
Switch on the drone.
The blue LED light on the drone will flash. The drone is now
ON.
3.
Place the drone on a FLAT SURFACE with the blue LED
light furthest away from you. If the drone is not positioned on
a flat surface, this may prevent the rotor blades from spinning
correctly.
4.
Turn the handset ON. The handset will beep.
5 & 6.
Push ‘Control Stick A’ up and then down to pair the handset with
the drone. The LED lights will stop flashing
7.
The handset and
drone are now synchronised and active.
8.
Slowly push ‘Control
Stick A’ up.
9.
Your drone will start to take off.
D. FLYING
Take Off and Land:
Slowly push the ‘Control Stick A’ up to control
take off and increase the height. Slowly push down to reduce height
and land. ‘Control Stick A’ is extremely sensitive so please move
gently. Move down ‘Control Stick A’ to bring the drone to a landing.
Turn Left and Right:
Whilst holding the drone in a controlled
hover, push ‘Control Stick A’ right to turn clockwise and left to turn
anti-clockwise. Please ensure that you maintain the hover with
‘Control Stick A’.
Fly Forward and Back:
Whilst holding the drone in a controlled hover, push the ‘Control
Stick B’ slowly forward to fly forwards and back to fly backwards.
Whilst flying forwards/backwards continue to control ‘Control
Stick A’ to adjust left/right turn and maintain height.
Sideways Left and Right:
Whilst holding the drone in a
controlled hover, push ‘Control Stick B’ slowly to the right to fly
the drone sideways to the right, or to the left to fly the drone
sideways to the left. Ensure there is a minimum of 3 metres
space surrounding the drone.
E. TRIM CONTROL
1. If the drone leans undesirably either forwards or backwards.
Push the trim button the opposite direction to the undesired
movement. For example, if the drone is leaning forwards while
hovering, push the backward trim button to correct.
2. If the drone leans undesirably either left or right.
Push the trim button the opposite direction to the undesired
movement. For example, if the drone is leaning left while
hovering, push the right lean trim button to correct.
F. STABILITY RESET
If the product becomes too unstable, push both left and right
joysticks to the bottom left position and hold for a few seconds.
The handset will beep. The LED lights on the drone will flash. Your
drone is now reset and stable.
G. STUNT 360
1.
Fly the drone in a controlled hover at a minimum of 3 metres
from the ground. Ensure there is enough clear space with no
objects nearby.
2.
Press the ‘Stunt 360’ button (top right shoulder)
and move ‘Control Stick B’ in the direction you want to flip 360˚
(forward/backward/left/right) and the drone will flip in that
direction. Repeat steps 1 - 2 to perform another flip.
H. SPEED SETTING
Press the speed button to adjust the speed level of your drone
(Refer to page 2 & 6).
1.
Press once for normal speed (1 ‘Beep’)
2.
Press again for expert speed (2 ‘Beeps’).
3.
Press again for pro
speed (3 ‘Beeps’).
I. HEADLESS FUNCTION
The Headless Mode feature allows the user to operate the drone
without worrying about the orientation of the drone. This feature is
great for beginners as it reduces the steepness of learning curve.
1.
Place the drone on a FLAT SURFACE with the blue LED lights
furthest away from you.
2.
Press the Headless Mode button. The
drone will beep intermittently and the lights will flash on the drone,
when in headless mode.
J. HOME FUNCTION
During flight, with the blue LED furthest away from you, press
the home function button once and the drone will autonomously
return from a far away distance. Push ‘Control Stick B’ forward
when the drone is within close proximity.
TROUBLESHOOTING
Drone blades will NOT turn
- Turn drone ON / Ensure drone is
fully charged / Check batteries in the handset / Turn drone and
handset OFF and ON again, and re-synchronise.
Drone stops
during flight
- Ensure drone is flown within the 25m range /
Replace batteries in the handset / Charge drone.
Drone is NOT
charging
- Ensure USB charging cable is correctly connected
to the battery connector.
Drone moving in an undesired
direction
- Use the trimming buttons on the handset to precision
trim (see page 5 for reference)
. Drone LED lights are flashing,
but no beep sound, during use -
Battery is low. Ensure drone
is fully charged. Visit our website for any further troubleshooting
questions.
Drone is erratic and will not function correctly
-
Rotor blades could be installed incorrectly. Ensure the rotor
blades are installed correctly. (see page 3 for reference).
Warning!
The manufacturer is not responsible for any radio or television
interference which may be caused by unauthorised modifications
7
