background image

English

5

English

4

Never disconnect the protective mains earth connection.

High loudspeaker levels can cause permanent hearing damage. You should 
therefore avoid the direct vicinity of loudspeakers operating at high levels. Wear 
hearing protection if continuously exposed to high levels.

If the product does not operate normally when the operating instructions are 
followed, then refer the product to a quali

Ä

ed service engineer.

The U.

:

.

overnment

6

ccupational 

:

afety and Health Administration 

6:

HA

 has 

speci

Ä

ed the following permissible noise level exposures

!

Duration Per Day In Hours 

:

ound 

3

evel d

)

A, 

:

low Response

8  

 

90

6  

 

92

4  

 

95

3  

 

97

2  

 

100

1½  

 

102

1  

105

½  

110

¼ or less    

115

According to 

6:

HA, any exposure in excess of the above permissible limits could 

result in some hearing loss.

Ear plug protectors in the ear canals or over the ears must be worn when operating 
this ampli

Ä

cation system in order to prevent a permanent hearing loss if exposure is 

in excess of the limits as set forth above. To ensure against potentially dangerous 
exposure to high sound pressure levels, it is recommended that all persons 
exposed to equipment capable of producing high sound pressure levels such as 
this ampli

Ä

cation system be protected by hearing protectors while this unit is in 

operation.

Warning!

Important safety information!

READ THE FOLLOWING INFORMATION CAREFULLY. SAVE ALL 
INSTRUCTIONS FOR FUTURE REFERENCE!

Follow all warnings and instructions marked on the product!

Danger!  High internal operating voltages.

Do not open the equipment case. There are no user serviceable parts in this 
equipment. Refer all servicing to quali

Ä

ed service personnel. 

Clean only with a dry cloth.

Condensation can form on the inside of an ampli

Ä

er if it is moved from a cold 

environment to a warmer location. 

)

efore switching the unit on, it is recommended 

that the unit be allowed to reach room temperature. 

Unauthorised modi

Ä

cation of this equipment is expressly forbidden by 

)

lackstar 

Ampli

Ä

cation 

3

td.

Never push objects of any kind into ventilation slots on the equipment casing.

Do not expose this apparatus to rain, liquids or moisture of any type. 

Do not place this product on an unstable trolley, stand or table. The product may 
fall, causing serious damage to the product or to persons!

Do not cover or block ventilation slots or openings. This unit must only be used in 
a well ventilated area and never switched on when it is within a poorly ventilated 
space, such as a bookcase.

This product should not be placed near a source of heat such as a stove, radiator, 
or another heat producing ampli

Ä

er.

Use only the supplied power cord which is compatible with the mains voltage supply 
in your area.

Power supply cords should always be handled carefully and should be replaced if 
damaged in any way.

Never break off the earth 

ground

 pin on the power supply cord.

The power supply cord should be unplugged when the unit is to be unused for long 
periods of time.

An apparatus with Class I construction should be connected to a mains socket 
outlet with a protective earthing connection.

The mains plug of the power supply cord should remain readily accessible.

)

efore the unit is switched on, the loudspeaker should be connected as described 

in the handbook using the lead recommended by the manufacturer.

Always replace damaged fuses with the correct rating and type.

All electrical and electronic products should be disposed of separately 
from the municipal waste stream via designated collection facilities 
appointed by the government or the local authorities.

Summary of Contents for ID:10TVP












Reviews: