background image

7

operations for the parking light output: parking

lights turn on for 30 seconds with unlock,

parking light output can be set to exchange pin

locations with trunk release output to provide

negative parking light and positive trunk release

outputs, or parking lights can be set to flash

twice with unlock.
3. Horn Honk Pulse Length. Some vehicle

horns may require a longer or shorter pulse to

provide the best horn honk sound. The horn

honk pulse can be set for 5ms, 15ms, or 10ms.
4. Button 4 Operation. Button 4 can be

programmed to operate in one of three ways: as

a dedicated button for trunk release (the Car

Finder feature is lost), as a no function button,

and as a dedicated Car Finder feature button.

Menu 3

1. Door Lock Control For Factory Alarm. This

feature allows three different door lock control

functions to aid integration with factory security

systems. Setting 1 pulses unlock before start and

pulses lock both after starting and after

shutdown. Setting 2 pulses the lock only after

remote start shutdown. Setting 3 provides only

normal operation for the lock/unlock pulses.
2. Engine Type. Selects between gasoline and

diesel engine types. There are three operation

choices for diesel engine equipped vehicles, a

15-second timer mode for vehicles without a

glow plug wire and both positive and negative

glow plug monitor modes for vehicles with a

wait-to-start indicator light.

(+) Glow Plug Monitor Mode:

For vehicles with a

wait-to-start wire that shows +12V when the

indicator light goes out, connect to the proper

vehicle wire and set Engine Type to setting 1.

15-Second Timer  Mode:

For diesel engines where

a proper glow plug wire cannot be located, set

the Engine Type to setting 2 which automatically

cranks the starter after a 15-second warm up

period for the glow plugs.

PROGRAMMABLE FEATURES

(default settings in bold)

Step Function

Setting 1

Setting 2

Setting 3

Menu 1

1.

Ignition Lock/Unlock

On/On

On/Off

Off

2.

Horn Honk Settings

Silent L/UL

No honk w/start

Normal

3.

Door Lock/Unlock Pulses 

.75sec / UL x 2

3 seconds

.75 seconds

4.

Short Unlock/Disarm Pulse 

.125 sec

Normal

Menu 2

1.

Valet Mode Timing

Hold 15 seconds

Hold 5 seconds

2.

Parking Light Output

30 seconds w/UL

Swap w/ Trunk Output 

Flash 2x w/UL

3.

Horn Honk Pulse

5ms (short)

15ms (long)

10ms (normal)

4.

Button 4 Operation

Trunk Release

Not used

Car Finder

Menu 3

1.

Lock Control w/ Start Functions UL before/L after 

L after shutdown only

Normal L/UL pulses

2.

Engine Type

Diesel (+) Glow Plug Diesel 15 sec Timer

Gasoline/(-) Glow

3.

Factory Alarm Rearm Pulse

After start & w/L

After start only

After stop & w/L

4.

Engine Run Time

4 minutes

45 minutes

15 minutes

5.

Crank Time

10 seconds max

3 seconds max

5 seconds max

6.

GWR / Starter Defeat

Starter Defeat/A-G Passive Starter Defeat

GWR w/A-G

7.

Start Button 

Press 2x within 3 sec

Press once

BW651 final.qxd  10/18/2005  10:58 AM  Page 7

Summary of Contents for 651













Reviews: