background image

INSTRUCTION MANUAL.

15

 Ailerons :  15mm up     15mm down
 Elevator :  15mm up     15mm down
 Rudder :   25mm right   25mm left

 

  

  

1) We highly recommend setting up a

plane using the control throws listed.

 

  

  

2) The control throws should be measured

at the widest point of each control surface.

 

  

  

3) Check to be sure the control surfaces

move in the correct directions.

CONTROL THROWS.

 

  

  

1) It is critical that your airplane be balanced

correctly. Improper balance will cause your
plane to lose control and crash.

    THE CENTER OF GRAVITY IS LOCATED

9cm

 BACK FROM THE LEADING EDGE OF

THE WING, AT THE FUSELAGE.

BALANCING.

 

  

  

2)  Turn the airplane upside down. Place

your fingers on the masking tape and carefully
lift the plane .

CG

9CM

Ailerons Control

 

  

  

1) Completely charge your transmitter and

receiver batteries  before your first day of flying.

 

  

  

2) Check every bolt and every glue joint in

your plane to ensure that everything is tight
and well bonded.

 

  

  

3)  Double check the balance of the

airplane.

 

  

  

4) Check the control surface.

 

  

  

5) Check the receiver antenna . It should

be fully extended and not coiled up inside the
fuselage.

 

  

  

6) Properly balance the propeller.

We wish you enjoy.

PRE-FLIGHT CHECK.

Summary of Contents for Liberty 182
















Reviews: