background image

ENGLISH • 23

FUEL

Fueling and refueling the brush cutter

 Warning! Use of unmixed, improperly mixed, or fuel 

older than 90 days, (Stale Fuel), may cause hard starting, 

poor performance, or severe engine damage and void 

the product warranty. Read and follow instructions in the 

“Storage Section” on this manual.

 Warning! Alternative fuels, which contain, Methanol 

or any fuels not meeting BLACK+DECKER requirements 

are NOT approved for use in BLACK+DECKER 2-stroke 

gasoline engines. Use of alternative fuels may cause 

performance problems, loss of power, overheating, 

fuel vapor lock, and unintended machine operation, 

including, but not limited to, improper clutch engagement. 

Alternative fuels may also cause premature deterioration 

of fuel lines, gaskets, carburetors and other engine 

components.

 

Fuel requirements

Gasoline: Use 89 Octane (or higher) unleaded gasoline 

known to be good quality and commonly used in the local 

automotive segment. Should it contain Ethanol, make sure 

it has low contents.

Two Stroke Oil: A two-stroke engine oil meeting ISO-

L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards 

must be used. Castrol brand A747 2-Stroke Oil meets 

these standards. Engine problems due to inadequate 

lubrication caused by failure to use an ISO-L-EGD (ISO/

CD 13738) and J.A.S.O. FC/FD certified oil will void the 

two-stroke engine warranty.

DANGER

Fuel is very flammable. Use extreme care when mixing, 

storing, or handling or serious personal injury may result.

 

f

Use an approved fuel container.

 

f

Do not smoke nera fuel.

 

f

Do not allow flames or sparks near fuel.

 

f

Fuel tanks/cans may be under pressure. Always  

 

loosen fuel caps slowly allowing pressure to equalize.

 

f

Never refuel a unit when the engine is HOT or  

 

RUNNING.

 

f

Do not fill the fuel in indoor areas. Always fill the fuel  

 

in outdoor over bare ground.

 

f

Do not overfill fuel tank. Wipe up spills immediatly.

 

f

Securely tighten fuel tank cap and close fuel container  

 

after refueling.

 

f

Inspect for fuel leakage. If fuel leakage is found,  

 

do not start or operate unit leakage is repaired.

 

f

Move at least 3m (10ft.) from refueling location before  

 

starting the engine.

Fuel to oil mix – 40:1 Ratio

Fuel ration other than 40:1 may cause 

damage engine. Ensure mixture is 

correct.

Mixing instructions

1.   Fill an approved fuel container with half of the  

 required amount of gasoline.

2.   Add the proper amount of 2-stroke oil to gasoline.

3.   Close container and shake to mix oil with gasoline.

4.   Add remaining gasoline, close fuel container, and remix.

 

 Important! Inspect fuel tank making sure it is clean. 

Always use fresh fuel.  

AFTER USE

DO NOT store a unit with fuel in its tank. Leaks can occur. 

Return unused fuel to an approved fuel storage container. 

 

STORAGE

As a precaution, store fuel in an approved, airtight container. 

Store in a well-ventilated, unoccupied building, away from 

sparks and flames. Check for local ordinances on type and 

location of storage container.

OPERATION

Starting cold engine (Fig. F, G and H)

1.  Stop Switch: Move stop switch button (1) forward  

 

away from the STOP position.

2.   Choke: Move choke lever (2) to COLD START 

   

 position.

3.   Purge Bulb: Pump purge bulb (3) 7 to 10 times  

 

until fuel is visible and flows freely in the clear fuel  

 

tank return line.

4.   Recoil Starter: Firmly grasp right hand grip and  

 

throttle trigger lockout with left hand and fully depress  

 

throttle trigger to wide open position. Rapidly pull  

 

recoil starter handle/rope (4) until engine fires  

 

(or maximum five -5- pulls).

5.   Choke: After engine fires (or 5 pulls), move choke  

 

lever back to Run 

 position. Hold throttle trigger  

 

and throttle trigger lockout fully depressed, and  

 

pull recoil starter handle/rope until engine starts and  

 

runs. Release throttle trigger, and allow unit to warm  

 

up at idle for several minutes. Note: If engine does  

 

not start with choke in RUN position after 5 pulls,  

 

repeat instructions 2 to 5.

6.   Throttle Trigger: After engine warm-up, gradually  

 

depress throttle trigger to increase engine RPM to  

 

operating speed.

Starting warm engine (Fig. F, G and H)

The starting procedure is the same as COLD START 

except DO NOT close the choke, and do not hold throttle 

trigger fully depressed.

Summary of Contents for GST33




























Reviews: