![background image](http://html1.mh-extra.com/html/black-decker-1/g915/g915_original-instructions-manual_2765771010.webp)
ENGLISH
(Original instructions)
• Place the outer flange (13) onto the
spindle. When fitting a grinding disc,
the raised centre on the outer flange
must face towards the disc (A in fig. E).
When fitting a cutting disc, the raised
centre on the outer flange must face
away from the disc (B in fig. E).
• Keep the spindle lock (3) depressed
and tighten the outer
flange using the
two-pin spanner (14) (fig. F).
Removing
• Keep the spindle lock (3) depressed
and loosen the outer flange (13) using
the two-pin spanner (14) (fig. F).
• Remove the outer flange (13) and the
disc (11).
Fitting and removing sanding discs
(fig. F & G)
For sanding, a backing pad is required.
The backing pad is available from your
BLACK + DECKER dealer as an accessory.
Fitting
• Place the inner flange (10) onto the
spindle (5) as shown (fig. G). Make sure
that the flange is correctly located on
the flat sides of the spindle.
• Place the backing pad (15) onto the
spindle.
• Place the sanding disc (16) onto the
backing pad.
• Place the outer flange (13) onto the
spindle with the raised centre facing
away from the disc.
• Keep the spindle lock (3) depressed
and tighten the outer flange using the
two-pin spanner (14) (fig. F). Make sure
that the outer flange is fitted correctly
and that the disc is clamped tightly.
Removing
• Keep the spindle lock (3) depressed
and loosen the outer flange (13) using
the two-pin spanner (14) (fig. F).
• Remove the outer flange (13), the
sanding disc (16) and the backing pad
(15).
Residual risks
Additional residual risks may arise when
using the tool which may not be included
in the enclosed safety warnings. These
risks can arise from misuse, prolonged use
etc.
Even with the application of the relevant
safety regulations and the implementation
of safety devices, certain residual risks
cannot be avoided. These include:
• Injuries caused by touching any
rotating/moving parts.
• Injuries caused when changing any
parts, blades or accessories.
• Injuries caused by prolonged use
of a tool. When using any tool for
prolonged periods make sure you take
regular breaks.
• Impairment of hearing.
• Health hazards caused by breathing
dust developed when using
your tool (example:- working
with wood, especially oak, beech
and MDF).
Use
Warning!
Let the tool work at its
own pace. Do not overload.
• Carefully guide the cable in order to
avoid accidentally cutting it.
• Be prepared for a stream of sparks
when the grinding or cutting disc
touches the workpiece.
• Always position the tool in such a way
that the guard
provides optimum protection from the
grinding or cutting disc.
Switching on and off
• To switch on, slide the on/off switch (1)
forward. Note that the tool will continue
running when you release the switch.
• To switch off, press the rear part of the
on/off switch.
Warning!
Do not switch the tool off
while under load. Hints for optimum
use
10
Summary of Contents for G915
