![background image](http://html1.mh-extra.com/html/black-decker-1/g915/g915_original-instructions-manual_2765771008.webp)
ENGLISH
(Original instructions)
Additional safety warnings specific for
abrasive cuttingoff operations
•
Do not “jam” the cut-off wheel or
apply excessive pressure. Do not
attempt to make an excessive depth
of cut.
Over stressing the wheel
increases the loading and susceptibility
to twisting or binding of the wheel in
the cut and the possibility of kickback
or wheel breakage.
•
Do not position your body in line with
and behind the rotating wheel.
When
the wheel, at the point of operation,is
moving away from your body, the
possible kickback may propel the
spinning wheel and the power tool
directly at you.
• When wheel is binding or when
interrupting a cut for any reason,
switch off the power tool and hold
the power tool motionless until the
wheel comes to a complete stop.
Never attempt to remove the cut-off
wheel from the cut while the wheel
is in motion otherwise kickback may
occur.
Investigate and take corrective
action to eliminate the cause of wheel
binding.
• Do not restart the cutting operation
in the workpiece. Let the wheel reach
full speed and carefully re-enter
the cut.
The wheel may bind, walk
up or kickback if the power tool is
restarted in the workpiece.
• Support panels or any oversized
workpiece to minimize the risk of
wheel pinching and kickback.
Large
workpieces tend to sag under their own
weight. Supports must be placed under
the workpiece near the line of cut and
near the edge of the workpiece on both
sides of the wheel.
• Use extra caution when making a
“pocket cut” into
existing walls
or other blind areas.
The protruding
wheel may cut gas or water pipes,
electrical wiring or objects that can
cause kickback.
Safety warnings specific for sanding
operations
• Do not use excessively oversized
sanding disc paper. Follow
manufacturers recommendations,
when selecting sanding paper. Larger
sanding paper. extending beyond
the sanding pad presents a laceration
hazard and may cause snagging,
tearing of the disc orkickback.
Safety warnings specific for polishing
operations
•
Do not allow any loose portion of the
polishing bonnet or its attachment
strings to spin freely. Tuck away or
trim any loose attachment strings.
Loose and spinning attachment strings
can entangle your fingers or snag on
the workpiece.
Safety warnings specific for wire
brushing operations
•
Be aware that wire bristles are thrown
by the brush even during ordinary
operation. Do not overstress the wires
by applying excessive load to the
brush.
The wire bristles can easily
penetrate light clothing and/or skin.
•
If the use of a guard is recommended
for wire brushing, do not allow any
interference of the wire wheel or
brush with the guard.
Wire wheel or
brush may expand in diameter due to
work load and centrifugal forces.
Safety of others
• This appliance is not intended for
use by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision or
instruction concerning the use of the
appliance by a person responsible for
the their safety.
• Children should be supervised to
ensure that they do not play with
the appliance.
6
8
Summary of Contents for G915
