manualshive.com logo in svg

Black Box Peripheral Sharer 2 to 1, Manual

Share
Download
Black Box Peripheral Sharer 2 to 1 Manual Download Page 9

9

Peripheral Sharer

holding down key when 
powering on the unit.

Software 

— Supplied on a 3.5" PC

disk (virus-checked).  Contains
the following software utilities:

SMARTKEY

: DOS and Windows

peripheral-selection software.

SMARTLOG

: Windows CD-

ROM/tape-drive selection 
software.

DOWNLOAD

: Used to update 

the unit’s EEPROM options.

Cable Types 

—

PC to Peripheral Sharer

:  DB25

male connectors on both ends, 
shielded, pinned straight-
through (part number EQN200).

Peripheral Sharer to Printer

:  DB25

male to 36-pin male printer cable,
shielded, all ground lines 
connected (part number 
EQN202).

Peripheral Sharer to Other Devices

:

Use PC to Peripheral Sharer
cable.

Cable Lengths 

— Lengths supported

vary considerably with cable type
and PC/peripheral specifications.
IEEE 1284 twisted-pair cables
and high-quality cables generally
support longer distances.  
Maximum recommended cable
lengths are:

PC to Peripheral Sharer

: 32.8 ft.

(10 m) for printers, 22.9 ft. 
(7 m) for tapes/CD-ROMs.

Peripheral Sharer to Peripheral

:

6.5 ft. (2 m)

Power 

— 115 or 230-VAC, 5 VDC,

500 mA

Size 

— 3.7"H x 8.5"W x 1"D

(9.5 x 21.5 x 2.5 cm)

Summary of Contents for Peripheral Sharer 2 to 1




































Reviews:

No comments

Brands by name

Popular brands

Load more brands