Black Box LGB5124A User Manual Download Page 1

Page: 1 / 257

BLACK BOX

Provides (20) Gigabit Ethernet SFP, (4) Gigabit

Ethernet Combo RJ-45/SFP, and (4) 1G/10G SFP+

connections.

This manual contains information for firmware version 1.59.

SFP Managed Switch Eco User’s Manual

LGB5128A

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

Customer

Support

Information

Summary of Contents for LGB5124A


































































































































































































































































Search results

Summary of Contents for LGB5124A

Reviews:

Related manuals for LGB5124A

Brands by name

Popular brands

Black Box LGB5124A, User Manual

Search results

Summary of Contents for LGB5124A

Reviews:

Related manuals for LGB5124A

Brands by name

Popular brands