background image

 724-746-5500   |   blackbox.com

Page 74

Black Box DeeSL.2 Ethernet Extender

The table below explains the commands available in the main menu:

show

View system configuration

write

Update flash configuration

reboot

Reset and boot system

ping

Packet internet groper command

admin

Setup management features

utility

TFTP upgrade utility

exit

Quit system

Table 13: 

Enable Command Menu

Command

Description

enable

Change the configuration and write changes to nonvola-
tile RAM (NVRAM)

setup

Initially configure the LB52xA-KIT

status

View the status of the LB52xA-KIT

show

Show the system and configuration

write

Update flash configuration. After you have completed all 
desired changes, make sure to write the new configura-
tion to NVRAM. Use the write command to save your 
changes and reboot the system or all of your changes 
will not take effect.

reboot

Reset and reboot system. After you have completed all 
desired changes, make sure to write the new configura-
tion to NVRAM. Use the reboot command to restart the 
system or all of your changes will not take effect.

ping

Check the connection to the LB52xA-KIT

admin

Set up advanced management features.

utility

Upgrade software and backup/restore the current con-
figuration

exit

Log out of the system

Summary of Contents for LB522A-KIT

















































































































Reviews: