Black Box LB522A-KIT Manual Download Page 82 | Manualshive

Page: 82 / 112

background image

724-746-5500 | blackbox.com

Page 82

Black Box DeeSL.2 Ethernet Extender

Port-Based VLAN. With port-based VLAN, the port is assigned to a specific VLAN
independent of the user or system attached to the port. This means all users attached
to the port should be members in the same VLAN. The network administrator typically
performs the VLAN assignment. The port configuration is static and cannot be auto-
matically changed to another VLAN without manual reconfiguration.

You can set up Port-Based VLAN using the method for 802.11Q. However, VID, PVID
or link type do not matter for Port-Based VLAN. Use the list command to check the
status of the VLAN.

-----------------------------------------------------------------------------
Virtual LAN Parameter
VLAN Mode : Port-Based VLAN
Virtual LAN Table
No LAN1 LAN2 LAN3 LAN4 Line Sniffing
-- ---- ---- ---- ---- ---- --------
1 1 1 1 1 1 1
2 - - - - - -
3 - - - - - -
4 - - - - - -
5 - - - - - -
6 - - - - - -
7 - - - - - -
8 - - - - - -
-----------------------------------------------------------------------------

5.8.4 QoS

Quality of Service (QoS)

refers to both a network's ability to deliver data with mini-

mum delay, and the networking methods used to control the use of bandwidth. Without
QoS, all traffic date is equally likely to be dropped when the network is congested. This
can cause a reduction in network performance and mark the network inadequate for a
time-critical application such as video-on-demand.

8

PVID

Link

Type

Access

Trunk

Access

Trunk

Access

Trunk

Access

Trunk

Access

Trunk

Access

Trunk

Table 19:

802.1Q VLAN Options

1

2

3

4

5

6

No

VID

LAN1

LAN2

LAN3

LAN4

Line

Sniffing

«
...
80
81
82
83
84
...
»

Summary of Contents for LB522A-KIT

















































































































Reviews:

No comments

Related manuals for LB522A-KIT

Brand: Fakir Pages: 72

Brand: MAGIMIX Pages: 65

Brand: IDK Pages: 104

eX-1C/CM110-BNC

Brand: Perle Pages: 15

Brand: APURO Pages: 8

Brand: DigitaLinx Pages: 6

Brand: SOLAC Pages: 60

Brand: W&T Pages: 28

SecureMesh XTEN-1000

Brand: Trilliant Pages: 21

Brand: Fortress Technologies Pages: 8

Brand: Altechna Pages: 12

Brand: CTC Union Pages: 2

Brand: Vitek Pages: 36

PowerMid Classic PM10C

Brand: Ebode Pages: 28

Brand: Digitus Pages: 9

Brand: Renkforce Pages: 8

Brand: J-Tech Digital Pages: 11

Brand: ALLEN & HEATH Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands