Black Box IE GIGA MC TX/SFP User Manual Download Page 35

Page: 35 / 56

Chapter 3: Configuration

Page 22

724-746-5500 | blackbox.com

LGC340A

3.5.3.3 Accounts

The following are the three levels for CLI or Telnet account access:
User:

View status, change own password, and reboot.

Operator:

All User privileges mentioned above, plus ability to

change settings.

Administrator: Operator privileges mentioned above, plus ability to

add/delete
accounts and reinitialize the unit to default settings

(cleandb).

3.5.3.4 VLAN Configuration

The ports can be assigned as a trunk or access port.

When configuring a trunk port, an Ethertype can be user-defined (a trunk port is

also defined as a provider port based on 802.1ad). If an Ethertype value

comes in a trunk port and is different than the user-defined Ethertype, it will be

treated as an unrecognized VLAN tagged frame. If configuring the port as an

access port, enter a VLAN ID between 1 and 4,094. Possible priority settings

are 0 (lowest priority) through 7 (highest priority).

Chapter 4: Install the IE GIGA MC TX/SFP

LGC340A

724-746-5500 | blackbox.com

Page 35

4. Install the IE GIGA MC TX/SFP

The IE GIGA MC TX/SFP has a small form factor making it ideal for installation

in locations with limited space.

4.1 Powering the IE GIGA MC TX/SFP

The IE GIGA MC TX/SFP includes multiple powering options:

•

AC adapter

•

The 4-terminal DC power block

•

An optional IE-Power/5V DIN railmount power supply, extended

temperature

•

An optional Double-USB Power Cable (available from Black Box)

IE GIGA MC TX/SFP with optional DIN railmount power supply

4.1.1 DC Terminal Block Wiring Instructions

The IE GIGA MC TX/SFP can also be powered with the DC terminal block.

From a power source, connect to any one positive and any one negative

terminal on the IE GIGA MC TX/SFP.

TELCO (-48)

NOTE

When using stranded wire, the leads should be tinned. The DC terminal block is

protected against polarity mis-wiring. AWG24 is recommended.

Summary of Contents for IE GIGA MC TX/SFP

























































Search results

Summary of Contents for IE GIGA MC TX/SFP

Reviews:

Related manuals for IE GIGA MC TX/SFP

Brands by name

Popular brands

Black Box IE GIGA MC TX/SFP, User Manual

Search results

Summary of Contents for IE GIGA MC TX/SFP

Reviews:

Related manuals for IE GIGA MC TX/SFP

Brands by name

Popular brands