Black Box IE GIGA MC TX/SFP User Manual Download Page 33

Page: 33 / 56

Chapter 3: Configuration

Page 24

724-746-5500 | blackbox.com

LGC340A

Press the down arrow on the computer keyboard to access additional

configuration selections.

WARNING

If a VLAN # is added to a port and is the same VLAN # assigned for a tag on

management traffic, saving these changes will disrupt management indefinitely.

Operation Mode 2 Port Based Xtra Tagging

Any port can be configured for extra tags on the frames.

Press the down arrow on the computer keyboard to access the additional

configuration commands.

Chapter 3: Configuration

LGC340A

724-746-5500 | blackbox.com

Page 33

After selecting the configuration file, the file upload process begins; when

completed, the user is notified of the status and also notified that a reboot is

necessary for the new configuration to become active:

By design, the IP Address configuration currently on the device is kept intact

and not overwritten by the new configuration file.

3.7 RJ-45 Data Port Pinout

The following table lists the pin

configuration for the RJ-45 Data

connector.

Pin

Signal

Name

1000M

Signal

Direction

10/100M

1 TXD1+ Out*
2 TXD1-

Out*

3 RXD2+ In*
4 D3+

5 D3-

6 RXD2-

In*

7 D4+

8 D4-

NOTE

The MDI/MDIX function will automatically adjust the direction of these signals to match

the connected unit when running 10/100Base-T. 1000Base-T will use all 4 pairs in full

duplex mode.

Pin 1

Summary of Contents for IE GIGA MC TX/SFP

























































Search results

Summary of Contents for IE GIGA MC TX/SFP

Reviews:

Related manuals for IE GIGA MC TX/SFP

Brands by name

Popular brands

Black Box IE GIGA MC TX/SFP, User Manual

Search results

Summary of Contents for IE GIGA MC TX/SFP

Reviews:

Related manuals for IE GIGA MC TX/SFP

Brands by name

Popular brands