manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, User Manual

Share
Download
Black Box 5000 MX215C, 5000 MX218C User Manual Download Page 231

Appendix D:  Messages

229

NO ASYNC CHANNELS

Info

A port or ports in the range selected is not

WITHIN RANGE

configured for async.

NODE-CHANNEL NOT AVAILABLE

Info

A link port number was entered when

ENTER CARRIAGE RETURN

a sync, async, or voice/fax channel number

TO CONTINUE

was required.

NODE ID ALREADY IN USE

Info

You are trying to configure a node ID that has
already been assigned in the network.

NODE NUMBER ALREADY

Info

You are trying to configure a node number

IN USE

that has already been assigned in the network.

ni

NO DIAL TONE LINK # 

ci

Event

The automatic dial-backup function was unable to
detect a dial tone when it went off hook to place a
call over the RX or TX dial lines.

ni

NO RECEIVER

Event

The ADB feature could not detect a dial tone at

DIAL TONE LINK 

ci

the receiver.  Check the phone connection.

NO REMOTE CONNECT

Info

The user is attempting a remote echo/fox test

ACTIVE

from Command Mode with no connection made.

NO SYNC CHANNELS

Info

A port or ports in the range selected are not

WITHIN RANGE

configured for sync.

ni

NO TRANSMITTER

Event

The ADB feature could not detect a dial tone

DIAL TONE LINK 

ci

at the transmitter.  Check the phone line.

NOT ALLOWED

Event

An invalid mode of operation has been entered; it
will not be supported.

NOT SUPPORTED

Info

The requested voice/fax configuration parameter
selected is not supported by your voice/fax module.

ni

NUMBER NOT

Event

The ADB number has not been configured for

CONFIGURED LINK 

ci

link 

ci

; the ADB operation cannot continue.

NUMERIC REQUIRED

Info

The entry received was not a number.

OPERATIONAL PROCESSOR FAIL

Event

The modem failed the self-test.  Contact your

FAIL

dealer.

OPERATIONAL PROCESSOR PASS

Event

Self-test complete.

OUT OF RANGE

Info

The range of numbers entered is not available in the
unit.

Screen Display Messages

Message

Message Type

Explanation

Summary of Contents for 5000 MX215C, 5000 MX218C













































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands