manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, User Manual

Share
Download
Black Box 5000 MX215C, 5000 MX218C User Manual Download Page 227

Appendix D:  Messages

225

ni

DIALING TX SECONDARY

Info

The modem is dialing the secondary TX dial

LINK # 

ci

line number.  This usually indicates that the call to
the primary TX number cannot be completed (the
number is busy, no answer, etc.).  This message is
displayed by the call-originating modem.

ni

DIAL LINE

Event

The dial line is dropped because of bad lines,

DROPPED LINK 

ci

DTR dropped, or RLSD lost.

DISABLED

Info

This function is disabled.

<DISCONNECTED>

Dialog

The connection has been broken.  Sent to call
originator only when switching is used (not for force-
connections).

DISCONNECT 

n/c n/c

Event

A pair of ports has been disconnected.

ni

DUPLICATE NODE-ID 

ci

Info

Two nodes in the network have the same ID.

<ENTER CLASS>

Dialog

Asks for the destination class name.

<ENTER CLASS

Dialog

Asks for the password associated with the 

PASSWORD>

destination port’s class.  If no password is
configured for the class, the user should type a

<cr>

.

<ENTER PASSWORD>

Dialog

Asks for a password associated with the signed on
port.

ni

FORCED DIAL

Event

The modem at node 

ni

on link 

ci

is configured

LINK 

ci

for forced dial mode.

ni

FORCED LEASE

Event

The modem at node 

ni

on link 

ci

is configured

LINK 

ci

for forced lease mode.

FOX TEST ACTIVE

Diagnostic

An async channel output test has been activated.

ILLEGAL INPUT

Info

The entry, as received, cannot be executed.  This
could be caused by an incorrect password, incorrect
broadcast message, or voice/fax extension number
that is too long.

ILLEGAL SELECTION

Info

The number entered is not on the list of items of the
displayed menu.

<INCOMPATIBLE>

Dialog

The attempted connection is not compatible with the
configuration.

Screen Display Messages

Message

Message Type

Explanation

Summary of Contents for 5000 MX215C, 5000 MX218C













































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands