manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, User Manual

Share
Download
Black Box 5000 MX215C, 5000 MX218C User Manual Download Page 136

Multiserver 5000

134

Table 11-2. The Command Mode

Option

Description

1.

Async Channel

A selection of loopback tests. See 

Section 12.3, Async Channel Loopback in the 

Loopback

Command Mode

, for a complete discussion of the tests.

2.

Local Channel

Provides control and modification of the locally connected port. After entering Command 

Configuration

Mode, the terminal user may reconfigure port parameters. All changes will take effect after
exiting the Command Mode. From this menu the following Asynchronous Channel
Characteristics can be set for the local port:  data rate, code level, parity, stop bits, echo, CR
delay, LF delay, and FF delay. A discussion of these characteristics is found in 

Section 9.3,

Asynchronous Channels

, and in 

Table 9-8

.

For ports connected via dialup modems, parameters reconfigured in the Local Channel
Configuration Menu remain in effect only for the duration of the call. When the call is
disconnected, the port converts back to the configuration set by the Command Facility.

For directly connected ports, the parameter changes remain in effect until changed in this
menu or in the Channel Characteristics menu.

After all the changes have been made for the port, return to the Command Mode Menu and
exit. Make the changes on the terminal to match the selected configuration. To ascertain the
correct configuration values for the the device connected to the port, consult its user manual.

3.

Command 

Accesses the Command Facility. Once you enter the Command Facility you cannot return to 

Facility Main

the Command Mode via a menu. Port or channel access to the Command Facility can be 

Menu

limited by in two ways:

• Access to the Command Facility can be limited by assigning a global password. See 

Section 11.5, Network Security

, for more information.

• The terminal accessing the Command Facility Main Menu must have the Command Facility 

Main Menu Access function enabled. The factory default is enable. (The Command Facility 
Main Menu Access function is option 10 of the Channel Features Menu. See 

Section 9.3, 

Asynchronous Channels

, and 

Table 9-11

for more information.)  

4.

Exit

Disconnects the terminal from the Command Mode.

Summary of Contents for 5000 MX215C, 5000 MX218C













































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands