manualshive.com logo in svg

Black Box 5000 MX215C, 5000 MX218C, User Manual

Share
Download
Black Box 5000 MX215C, 5000 MX218C User Manual Download Page 133

CHAPTER 11: Administration

131

After you have entered the correct channel, press
the EXEcute key.

To reset to a Default or Current Configuration,
press the EXEcute key at the appropriate screen.
You will be asked

ARE YOU SURE?

If you are,

press the EXEcute key again. Press any of the arrow
keys to abort the process.

C

OMMAND

F

ACILITY

R

ESET

Four types of software resets are available:  Node,
Link, Channel, and Integral LAN. The Reset Menu
is accessed from the Command Facility Main Menu. 

The Reset Menu is then displayed.

Each type of reset is described in Table 11-1.

Banner Message        Menu Functions

Administration

System

Clear Latched Alarms         System Reset         Restart Link          Reset Channel

Default Configuration          Current Configuration 

Key:

Press Down-Arrow Key                                          Press Right-Arrow Key

Figure 11-2.  Menu-flow diagram for LCD/Keypad resets.

COMMAND FACILITY MAIN MENU [node id]

RESET

10

RESET [node id]

1. NODE

2. LINK

3. CHANNEL

4. INTEGRAL LAN

CR - ACCEPT ENTRY

M  - MAIN MENU

ENTRY: 

Summary of Contents for 5000 MX215C, 5000 MX218C













































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands