6
•
Do not expose battery to fire or intense heat, as it may explode.
TROUBLESHOOTING
Unit Fails to Jump-Start
• Make sure unitʼs power switch is in the ON position.
• Check that Jump-Starter has a full charge.
• Make sure a proper polarity cable connection has been established (see
“Using the Unit as a Jump-Starter,” page 2).
SPECIFICATIONS
Jump-Start Clamps:
300 amps – heavy-duty
Jumper Cables:
#6AWG cable
Instant Amps:
300
5 Second Amp:
225
Battery High Density
AGM:
12 volt, 9 Ah, sealed, lead-acid
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www.blackanddecker.com
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailerʼs policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may
be required.Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state or province to province.
Should you have any questions, contact the manager of your nearest Black & Decker
Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT
: If your warning labels become illegible or are
missing, call
1-800-544-6986
for a free replacement.
5
CAUTION:
•
Make sure ON/OFF Power Switch are turned OFF during recharge as this
may slow recharge function.
AC Recharge
The AC recharge adapter is a UL listed “wall” type unit that operates from any
120 volt, 60 Hz AC supply that has a standard North American outlet. The
adapter has a barrel connector that plugs into the unitʼs recharge port.
Make sure the Jump-Starter Power Switch is turned OFF during AC recharge.
When an AC recharge adapter is plugged into the recharge port, the battery
charge level display will automatically activate. As recharge progresses, one red,
one yellow and one green LEDs will light, one by one. Charge the unit until the
battery charge level display lights or flashes the green FULL LED. Continue to
recharge for one to two hours, and then disconnect the recharge adapter. AC
recharge system is an automatic taper charge and can be left connected to the
main unit for long periods. (See Figure 1 for AC recharge port location).
Note: Make sure ON/OFF Safety Switch are Turned OFF During Recharge As This
May Slow Recharge
Replacement Parts
For replacement parts (bulbs, batteries, charging adapters, etc.), contact Black &
Decker Technical Support: toll free
1-800-544-6986.
There are no user
serviceable parts inside the unit. Periodically, the cables and connectors should
be inspected for damage, corrosion, dust, and dirt. If surfaces are dirty, they can
be wiped clean with a cloth moistened with water and a drop of detergent.
Contacts can be wiped clean with a dry cloth.
WARNING:
•
Do not operate unit if there is any evidence of damage. The product
must be returned to Black & Decker for testing and repair. Replace any
damaged charging adapters immediately before further use.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the lead
acid battery (or battery pack) indicates that the costs to recycle the battery (or
battery pack) at the end of its useful life have already been paid by Black &
Decker. In some areas, it is illegal to place spent lead acid batteries in the trash or
municipal solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established
programs in the United States and Canada to facilitate the collection of spent lead acid
batteries. Help protect our environment and conserve natural resources by returning the
lead acid battery to an authorized Black & Decker service center or to your local retailer
for recycling. You may also contact your local recycling center for information on where to
drop off the spent battery, or call
1-800-8-BATTERY.
WARNING:
•
Do not dispose of the battery in fire, as this may result in an explosion.
•
Before disposing of the battery, protect exposed terminals with
heavy-duty electrical tape to prevent shorting (shorting can result in
injury or fire).
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by Vector Products Inc.
701 East Joppa Road
Towson, MD 21286
90550872 Vec010BD:Vec010BD_Manual_042905 9/11/09 9:51 AM Page 4
