2. After obtaining the desired routing depth, release the spindle lock button. Continue turning
the base until the notch under the spindle lock button aligns with the next closet locking slot
in the base.
USING THE ROUTER
1. Make sure that the material to be cut is clamped down and is stable enough to support the
router during operation.
2. Use both hands on the power unit to control the router.
3. Move the router counterclockwise when cutting outside edges. Move clockwise when cutting
inside edges. See Figure 20.
FEEDING SPEED AND RATE OF CUT
Variation between materials and bit configurations dictates a wide variety of feed rates.
Experience is the best measure for determining feed rate. Become familiar with the sound and
feel of the router by making practice cuts in scrap material.
The router bit rotates at a very high speed and may heat up if the router is moved too slowly
through the wood and may cause burn marks. Feeding the router too fast or trying to remove
too much material in a single pass will overload the motor. Use two or more passes for extra-
large cuts (over 1/8" deep), especially in hard woods.
T-SQUARE GUIDE
A simple device for guiding the router when making straight cuts on flat surfaces is the home-
made T-square, Figure 21. This T-square can be easily made out of scrap lumber, but make
sure its edges are perfectly smooth and straight. It is placed on the surface being routed and
held in position by means of a clamp. The flat portion of the base of the router is guided firmly
along the edge of the T-square to make a straight cut. Measurements shown in Figure 21 are
ideal for most applications with the router. They may, however, be altered to suit your specific
needs.
GUIDE BUSHINGS
Two guide bushings are included for use when routing signs and templates. Attach the bushing
to the router base as shown in Figure 22 until you hear it snap into place. Use the 7/16” bushing
with 1/4” diameter or smaller router bits. Use the 5/8” diameter hinge butt guide bushing with
3/8” or smaller router bits.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-54-HOW-TO. (800-544-6986)
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service per-
sonnel, always using identical replacement parts.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation)
Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recy-
cle the battery (or battery pack) at the end of its useful life have already been paid
by Black & Decker. In some areas, it is illegal to place spent nickel-cadmium batter-
ies in the trash or municipal solid waste stream and the RBRC program provides an
environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs
in the United States and Canada to facilitate the collection of spent nickel-cadmium batteries.
Help protect our environment and conserve natural resources by returning the spent nickel-
cadmium battery to an authorized Black & Decker service center or to your local retailer for
recycling. You may also contact your local recycling center for information on where to drop
off the spent battery, or call 1-800-8-BATTERY.
9
SERVICE INFORMATION
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained per-
sonnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow
page directory under "Tools—Electric" or call: 1-800-544-6986.
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in materi-
al or workmanship. The defective product will be replaced or repaired at no charge in either
of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under "Tools-
Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state. Should you have any questions,
contact the manager of your nearest Black & Decker Service Center.
