Black & Decker GT100, Original Instructions Manual

Page: 7 / 76

7
ENGLISH
Fitting the guard ( fi g. A)
♦ Locate the guard (4) into the mounting bracket
(8).
♦ Push the guard into the bracket until it clicks
into place.
Warning! Never use the tool without the guard.
Connecting the tool to the mains ( fi g. B)
Unless the tool is fi tted with a mains cable, you will
need to connect an extension cable to the power
inlet.
♦ Connect the female socket of a suitable
extension cable to the power inlet of the tool.
♦ Loop the cable through the cable restraint (7)
as shown to prevent the extension cable from
becoming detached during use.
♦ Insert the mains plug into a mains outlet.
Warning! The extension cable must be suitable
for outdoor use. When using a cable reel, always
unwind the cable completely.
Residual risks.
Additional residual risks may arise when using
the tool which may not be included in the
enclosed safety warnings. These risks can arise
from misuse, prolonged use etc. Even with the
application of the relevant safety regulations and
the implementation of safety devices, certain
residual risks can not be avoided. These include:
♦ Injuries caused by touching any rotating/
moving parts.
♦ Injuries caused when changing any parts,
blades or accessories.
♦ Injuries caused by prolonged use of a tool.
When using any tool for prolonged periods
ensure you take regular breaks.
♦ Impairment of hearing.
♦ Health hazards caused by breathing dust
developed when using your tool (example:-
working with wood, especially oak, beech
and MDF.)
Use
Warning! Let the tool work at its own pace. Do not
overload.
♦ Carefully guide the cable in order to avoid
accidentally cutting it. A good way to control
the cable is by putting it over your shoulder.
♦ For your safety, this tool is equipped with
a double switching system. This system
prevents starting the tool inadvertently and will
only allow operation while holding the tool with
both hands.
Switching on and off
Switching on
♦ Take hold of the front handle (3) with one hand
so that the front handle switch (2) is pushed
into the body of the tool.
♦ With the other hand, squeeze the trigger switch
(1) to start the tool.
Switching off
♦ Release the handle switch (2) or the trigger
switch (1).
Warning! Never attempt to lock a switch in the on
position.
Hints for optimum use
♦ Start by trimming the top of the hedge. Slightly
tilt the tool (up to 15° relative to the line of cut)
so that the blade tips point slightly towards
the hedge (
fi g. C1). This will cause the blades
to cut more effectively. Hold the tool at the
desired angle and move it steadily along the
line of cut. The double-sided blade allows you
to cut in either direction.
♦ In order to obtain a very straight cut, stretch
a piece of string along the length of the
hedge at the desired height. Use the string as
a guideline, cutting just above it.
♦ In order to obtain fl at sides, cut upwards with
the growth. Younger stems move outwards
when the blade cuts downwards, causing
shallow patches in the hedge (
fi g. C2).
♦ Take care to avoid any foreign objects.
Especially avoid hard objects such as metal
wire and railings, as these could damage the
blades.
♦ Regularly oil the blades.
Guidelines for trimming (UK & Ireland)
♦ Trim hedges and shrubs with seasonal leaves
(new leaves every year) in June and October.
♦ Trim evergreens in April and August.
♦ Trim conifers and other fast growing shrubs
every six weeks from May until October.
Guidelines for trimming (Australia & New Zealand)
♦ Trim hedges and shrubs with seasonal leaves
(new leaves every year) in December and
March.
♦ Trim evergreens in September and February.
♦ Trim conifers and other fast growing shrubs
every six weeks from October until March.