4
ENGLISH
Electrical safety
This tool is double insulated in accordance with
EN 60335; therefore no earth wire is required.
Always check that the power supply corresponds to
the voltage on the rating plate.
To avoid the risk of electric shock, do not immerse
the cord, plug or motor unit in water or other liquid.
Features
1. Cap
2. Cap/blender location
3. Rotary switch
4. Motor spindle
5. Blender jar
6. Measuring cup
7. Blender cap
8. Processor bowl
9. Food pusher
10. Processor bowl lid
11. Tool storage disc
12. Spatula
13. Blade carrier
14. Chopping blade
15. Coarse shredding blade
16. Fine shredding blade
17. Slicing blade
18. Blender blade
19. Plastic whisking disc
Unpacking
X
Remove all packaging from the appliance,
X
Clean the appliance before first use.
Use
Warning!
Always place the appliance on a flat, clean and
non-slip surface before operating it.
Operating controls
The processor and blender control dials have the following
settings:
P
- Pulse
0
- Off
1
- Speed 1 (Low)
2
- Speed 2 (Middle)
3
- Speed 3 (High)
The speed can be adjusted while the processor or blender is
in use.
Warning!
Do not operate the food processor continuously
for more than 2 minutes. After operating the appliance
continuously for 2 minutes, let it cool down for at least 2
minutes before operating it again.
Using the processor bowl
The processor bowl (8) can be used to whisk, or chop large
quantities of food. See the section “Quantities and
processing times” in this manual.
X
Place the appliance on a flat surface and make sure that
the speed selector is set at
0
(off).
X
Make sure that the blender cap (1) or the blender jar (5)
is locked in position in the blender recess (2).
X
Rotate the processor bowl lid (10) in an anti-clockwise
direction and lift it away from the bowl (8).
X
Remove any accessories from the processor bowl (8).
X
Select the required accessory.
X
Make sure that the processor bowl (8) is locked in
position by rotating it in a clockwise direction.
The chopping blade (14), the knife frame (13) or the
whisk (19) can be placed directly over the central column of
the processor bowl (8). Rotating these items slowly will align
the hexagonal hole and drive on the motor spindle (4).
X
Add the ingredients and place the lid (10) on the
bowl (8), rotating it clockwise until it locks in place. The
long tab on the lid (10) will engage in the slot in the
upper housing.
X
Connect the appliance to the electrical supply and
select speed 1, 2, 3 or Pulse as required.
Additional ingredients can be added through the kidney-
shaped slot in the bowl lid (10) after removing the pusher (9).
The pusher must be used to guide the ingredients into the
path of the blade.
Warning!
Always use the pusher to assist in processing
food, never use your fingers.
Using the blades
Warning!
Make sure the food processor is unplugged from
the power source and switched off before fitting or removing
accessories.
The blades (14-17) must be fitted to the blade carrier (13)
before use.
X
Place the required blade on the blade carrier (13), and
slide it forward until the tab fits into the slot. The blade
must then be gently pushed until it locks in position. To
remove the blade, grip the rim underneath it and pull it
away from the blade carrier (13).
X
Once assembled, remove the processor bowl lid (10)
and, using the finger holes in the blade carrier (13) place
the blade carrier over the motor spindle (4).
X
Replace the processor bowl lid (10).
Summary of Contents for FP800
Page 1: ...English 3 Italiano 7 Español 12 Português 17 Eλληνικα 22 ...
Page 2: ...2 ...
Page 27: ......