4
ENGLISH
Assembly
Warning!
Before assembly, make sure that the appliance is
switched off and unplugged.
Fitting and removing the jug (fig. A)
◆
Position the jug (3) on the motor unit, aligning the lugs (6)
with the recesses (7).
◆
Fix the bowl by turning it counter-clockwise until the lugs
(6) engage in the slots (8).
◆
To remove the jug from the appliance, turn the jug
clockwise and take it off.
Assembling the jug (fig. A)
◆
Put the ingredients in the jug (3).
◆
Place the lid (4) on the jug.
◆
Fix the lid by turning it counter-clockwise until the tab (9)
is seated in the lug (10).
◆
To remove the lid from the jug, turn the lid clockwise and
take it off.
Removing and fitting the measuring cup (fig. A)
The pouring hole cover (5) integrated in the lid (4) is also
suitable for use as a measuring cup.
Removing
◆
Turn the cover counter-clockwise and take it off the lid.
Fitting
◆
Position the cover on the lid, aligning the lugs (11) with
the recesses (12).
◆
Fix the cover by turning it clockwise.
Use
Warning!
Always place the unit on a flat, clean and non-slip
surface before operating it.
Switching on and off
For your safety, this appliance is equipped with an interlock
system. This device avoids accidental starting if the appliance
is not assembled properly. Before switching on, make sure that
the jug (3) is fixed and check that the lid (4) is seated correctly.
◆
To switch on, move the speed control switch (1) to one of
the two positions: I (low speed) to II (high speed). It is
recommended to start at a low speed, then change to a
higher speed if necessary.
◆
To switch off, move the switch to position 0.
◆
To operate in the pulse mode, move the switch to position P.
Warning!
Do not operate the appliance continuously for more
than 2 minutes. After operating the appliance continuously for
2 minutes, let it cool down for at least 10 minutes before
operating it again. After operating the appliance for 4 cycles,
let it cool down to room temperature before operating it again.
Blending
◆
Add the required ingredients into the jug.
Warning!
Do not exceed the “max” marking of the graduation
on the jug.
◆
Fit the lid and pouring hole cover onto the jug.
◆
Operate the appliance as described above.
Ice crushing
◆
Open the pouring hole.
◆
Pour a small amount of water into the jug.
◆
Operate the appliance as described above.
◆
Carefully add ice through the pouring hole.
After use
◆
Remove the jug from the appliance.
◆
Remove the lid from the jug.
◆
Pour the ingredients out.
Cleaning and maintenance
Warning!
Before cleaning or maintenance, switch the
appliance off and unplug it.
◆
Wash the removable plastic parts in warm soapy water
and dry well.
◆
Wipe the motor unit with a damp cloth. Do not use any
abrasive or solvent-based cleaner.
Warning!
Do not immerse the appliance in water or any other
liquid.
Cleaning the blades (fig. A)
◆
Hold the jug (3) with one hand. With your other hand, turn
the blade assembly (13) clockwise to pull it off the jug.
◆
Clean the blades under running water.
◆
After cleaning, re-fit the blade assembly into the jug.
Turn the assembly counter-clockwise until the lugs (14)
secure behind the lugs (15) in the bottom of the jug.
Warning!
Be careful when cleaning the blades - they are
sharp. Do not attempt to sharpen the blades as this could
damage them.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
