5
English
Choose a Glass Tray (Fig. G)
Place a glass or shaker on either the glass shelf
17
or drip
tray
3
, depending on the height of the glass being used.
Refer to the cocktail image on the capsule
20
for glass style.
nOTE:
A glass or shaker must be in place before making a
drink to avoid spillage.
short glass:
1. Pull the glass shelf down so it stands straight out from
the tower
18
.
2. Place a small glass on the glass shelf.
On/Off (Fig. F)
WARNING:
Do not interact with the cocktail maker
while it is operating.
• To turn the cocktail maker on, push the "I" side of the power
switch
14
. The 4 strength LEDs
15
and 6 bottle LEDs
16
will blink. When they become solid, the cocktail maker is
ready to use.
• To turn the cocktail maker off, push the "O" side the side of
the power switch. All LEDs will turn off.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from power
source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
5. Slide the straw plug
11
all the way into the straw slot,
allowing the bottle to sit freely in its designated space.
Ensure the straw plug is fully seated in the slot
6. To lock it into place, push the straw lock down until it
clicks. Ensure the lever is fully down.
7. Repeat for all bottles.
iMPORTAnT:
Bottles must be placed in their designated space
to ensure the correct drink is dispensed. Names of the liquids are
located in each spot, indicating the appropriate liquid.
iMPORTAnT:
The following are the only liquids that should
be used with the appliance.
• Water
• Gin
• Rum
• Vodka
• Tequila
• Whiskey
Removing Bottles (Fig. E)
CAUTION:
Avoid spills while removing bottles.
1. Lift the straw lock
8
.
2. Slide the straw plug
11
and bottle off the cocktail maker.
3. Pull the bottle stopper
13
out of the bottle and remove
the straw
7
.
nOTE:
If the cocktail maker pauses for an empty bottle and you
press mix without replacing the bottle, it will skip to the next
bottle in the recipe. If that bottle is empty, it will pause again.
Refer to the PAUSE MODE section for more information.
Installing Bottles (Fig. D)
WARNING:
Only use water in the supplied water
bottle. Use of other liquids or substances in the water
bottle may result in damage to the appliance.
CAUTION:
Avoid spills while installing bottles.
nOTE:
It is recommended to use 750 ml bottles or smaller
to ensure all bottles sit on the bottle platform
6
without
hanging off the platform.
nOTE:
Bottles must fit between the bottle platform and the
top of the cocktail maker while standing.
1. Slide a straw
7
into a bottle so the straw tip
9
sits on the
bottom of the bottle.
2. Slide the bottle stopper
13
down the straw until it sits
fully in the top of the bottle.
3. Ensure the straw lock
8
is up.
4. Align the straw plug notch
12
with the straw slot
10
.
Installing Coaster (Fig. C)
1. Place the drip tray cover into the drip tray
3
so the
rounded and slanted corners of the cover line up with
the rounded and slanted corners of the drip tray.
2. Ensure the cover sits fully inside the drip tray.
3. To remove the cover, lift from the drip tray cover
finger
hole
5
.
Installing Cord (Fig. B)
1. Place the cocktail maker upright on a flat, level,
stable surface.
2. Insert the jack plug
1
of the cord into the plug port
2
.
3. Plug the other end of the cord into an outlet.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn appliance off and disconnect
appliance from power source before making any
adjustments or removing/installing attachments
or accessories.
An accidental start‑up can
cause injury.
IPM .....................impacts per minute
OPM .................... oscillations per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM ....................strokes per minute
A .........................amperes
W ........................watts
Wh ......................watt hours
Ah .......................amp hours
or AC ...........alternating current
or AC/DC .... alternating or direct
current
...................... Class II Construction
(double insulated)
no .......................no load speed
n .........................rated speed
PSI....................... pounds per square
inch
......................earthing terminal
.....................safety alert symbol
..................... visible radiation
do not stare into
the light
..................... wear respiratory
protection
..................... wear eye protection
..................... wear hearing
protection
..................... read all
documentation
..................... do not expose to
rain
