If you have any questions, call 1-800-9-BD TOOL (1-800-923-8665)
98020 (15 Minute Charger) only
1. Plug the charger into an appropriate AC power outlet. The charger will
beep twice and the red light will blink and then go off.
2. Insert the battery pack into the charger, as shown in Figure 1, making
sure the pack is fully seated in the charger. The red light will blink and
the charger will beep once indicating the charging process has started.
3. The battery pack will be fully charged in less than 15 minutes under
most conditions. This will be indicated by the red light remaining ON
and 3 audible beeps. The pack is fully charged and may be used at this
time or left in the charger.
Power Pack Insertion and Removal
To insert the power pack into your worklight, slide it into the end of the
light until it snaps into place. To remove the power pack, depress the
release buttons shown and withdraw the power pack.
Switch
To turn the light on, slide the switch forward. To turn it off, slide the switch
back.
Swiveling Head (Figure 2)
Your worklight has a swiveling head. To convert your light to a right angle
model, grasp the front end of the light forward of the switch and hold the
back end firmly. Twist the front end clockwise (as viewed from the lens)
until the head swivels 90 degrees and clicks into place. To return the head
to a straight position, rotate the head (as viewed from the lens)
counterclockwise until it clicks into the straight position.
Replacing the Light Bulb
Worklight Cat. No
Replacement Bulb Cat. No.
2909
29090
2912
29120
2914
29140
To replace the light bulb, first unscrew the lens holder. Pull the bulb out of
the spring, and insert a new bulb. Reinstall lens holder.
NOTE:Do not look directly into the worklight beam.
Spare Bulb Storage (Figure 3)
To store a bulb, unscrew the lens holder and remove it. Inside the body of
the worklight is the storage socket. To remove the bulb, pull it up and out
of the storage area. NOTE: Removing a pack from the charger and
immediately inserting it into the worklight may weaken bulb life.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
nickel-cadmium battery indicates that the costs to recycle the battery at
the end of its useful life have already been paid by B&D. In some areas, it
is illegal to place spent nickel-cadmium batteries in the trash or municipal
solid waste stream and the RBRC program provides an environmentally
conscious alternative.
RBRC in cooperation with B&D and other battery users, has established
programs in the United States to facilitate the collection of spent nickel-
cadmium batteries. Help protect our environment and conserve natural
resources by returning the spent nickel-cadmium battery to an authorized
service center or to your local retailer for recycling. You may also contact
your local recycling center for information on where to drop off the spent
battery.
One Year Free MaIntenance
All B&D tools for Industry and Construction are covered under a one year
free maintenance program where B&D will inspect your tool for safety and
provide necessary maintenance or repairs, including normal wear and tear
parts, for one year, FREE OF CHARGE.
Full Warranty
All B&D tools for Industry and Construction are warranted to be free of
any defects in materials or workmanship. Upon thorough examination of
tool, B&D will repair or replace, at our option, any product that is
determined to be defective.
Conditions
The service/safety check and the warranty do not apply to: repairs made or
attempted by anyone other than an authorized B&D service location;
misuse, abuse, neglect, improper application of the tool; missing parts; or
normal wear and tear (after first year of ownership). Please return the
complete unit, transportation prepaid, to any B&D factory owned or B&D
authorized service center location (list provided with tool or see Yellow
Pages under “Tools Electric”).
Fig. 1
Fig. 2
Fig. 3
LENS HOLDER
BULB
BATTERY RELEASE BUTTON
SPARE BULB STORAGE
POWER PACK (NOT INCLUDED)
SWIVELING HEAD
SWITCH
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
F#154530
(OCT96-2)
Printed in Taiwan
Copyright © 1996 Black & Decker
