BK Precision DAS240-BAT User Manual Download Page 64

Page: 64 / 75

CHAPTER 13. REMOTE INTERFACES

13.5 Control your device with DASLab

The DASLaB software manages configurations of your DAS240 device.

It helps you to :

• Open, modify and save your configurations

• Manage configurations remotly using network via Ethernet or WiFi

• Download your record files using network via Ethernet or WiFi

DASLaB is available on the sefram website:
http://www.sefram.com/en/products/recorders-dataloggers/DAS240-multi-channel-handheld-recorder.html

According to your needs, click on the right button. If you want manage your DAS240 using network, please
enter the IP address to establish the connection.

For every action, including opening, saving, sending or refreshing configurations, the left sliding menu makes you
able to apply it.

Figure 13.5: DASLab

13.6 Modbus (slave)

Modbus is a non-proprietary communication protocol. All Modbus frames are encapsulated into Ethernet
frames: it is called Modbus over TCP/IP.

That protocol is dialog based (question-answer) : the client (master) send a command, and then the server
(slave), send back wanted data.

Your instrument Sefram DAS240 includes a Modbus TCP Slave service.

For more explanations about Modbus protocol, please read the following link:

Summary of Contents for DAS240-BAT












































































Search results

Summary of Contents for DAS240-BAT

Reviews:

Related manuals for DAS240-BAT

Brands by name

Popular brands

BK Precision DAS240-BAT, User Manual

Search results

Summary of Contents for DAS240-BAT

Reviews:

Related manuals for DAS240-BAT

Brands by name

Popular brands