BK Precision DAS240-BAT User Manual Download Page 17

Page: 17 / 75

CHAPTER 2. SETUP

Note:

If errors persist, please contact B&K for further assistance.

2.2 Extension Modules

Up to 10 extension modules may be connected at a time.

Figure 2.4: Extension Module

To assemble multiple terminal block modules:

• Screw the electrical connectors’ plate to each additional extension

• Assemble the extension modules together

• Screw the plates with the adjacent modules

• Stick the additional adhesive buttress

• Connect the cable using unlocking levers

• Connect the cable on the DAS240 (must be powered off first)

• Switch on the unit.

Note:

The unit is delivered with a 70cm cable.

2.3 Making Measurement Connections

Using the terminal blocks provided with the unit. Figure

2.6

(Phoenix Contacts: SMSTB 2,5/3-ST5,08 - 1826296)

2.3.1 Voltage Measurement

Voltage measurement is performed between the + and - terminals of the relevant input. The “GND” terminal is
not used.

Summary of Contents for DAS240-BAT












































































Search results

Summary of Contents for DAS240-BAT

Reviews:

Related manuals for DAS240-BAT

Brands by name

Popular brands

BK Precision DAS240-BAT, User Manual

Search results

Summary of Contents for DAS240-BAT

Reviews:

Related manuals for DAS240-BAT

Brands by name

Popular brands