BK Precision DAS240-BAT User Manual Download Page 5 | Manualshive

Page: 5 / 75

background image

iv

known-operating voltage sources and test for both DC and AC voltages. Do not attempt any service or
adjustment unless another person capable of rendering first aid and resuscitation is present.

Do not insert any object into an instrument’s ventilation openings or other openings.

Hazardous voltages may be present in unexpected locations in circuitry being tested when a fault condition in
the circuit exists.

Fuse replacement must be done by qualified service-trained maintenance personnel who are aware of the
instrument’s fuse requirements and safe replacement procedures. Disconnect the instrument from the power line
before replacing fuses. Replace fuses only with new fuses of the fuse types, voltage ratings, and current ratings
specified in this manual or on the back of the instrument. Failure to do so may damage the instrument, lead to
a safety hazard, or cause a fire. Failure to use the specified fuses will void the warranty.

Servicing

Do not substitute parts that are not approved by B&K Precision or modify this instrument. Return the
instrument to B&K Precision for service and repair to ensure that safety and performance features are
maintained.

For continued safe use of the instrument

• Do not place heavy objects on the instrument.

• Do not obstruct cooling air flow to the instrument.

• Do not place a hot soldering iron on the instrument.

• Do not pull the instrument with the power cord, connected probe, or connected test lead.

• Do not move the instrument when a probe is connected to a circuit being tested.

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

«
...
3
4
5
6
7
...
»

Summary of Contents for DAS240-BAT












































































Reviews:

No comments

Related manuals for DAS240-BAT

Brand: Parker Research Corp Pages: 3

Brand: Campbell Pages: 362

Brand: Campbell Pages: 60

Brand: Campbell Pages: 116

Brand: Campbell Pages: 30

Brand: Campbell Pages: 55

IEM-100 Beltpack

Brand: DAPAudio Pages: 19

Brand: Veeder-Root Pages: 39

Brand: Veeder-Root Pages: 98

Brand: VECTECH Pages: 9

Brand: Yamaha Pages: 48

Brand: Omega Pages: 170

Brand: Topcon Pages: 62

Brand: CONDTROL Pages: 8

Brand: BYOGuitar.com Pages: 11

Brand: Siko Pages: 2

Brand: Sensia Pages: 139

Brand: York Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands