manualshive.com logo in svg

BJS Biotechnologies xxsealer, User Manual, Page: 18 / 26

Share
Download
BJS Biotechnologies xxsealer User Manual Download Page 18

P a g e

 | 

18 

 

7.3  Performing an xxplate Sealing Operation 

A typical operating sequence to seal an 

xxplate

 is: 

1)  Switch the unit on and set the sealing time to 1.5 seconds and the 

heater plate set-point temperature to 170ºC (using the method 
described above). These are the recommended setting for the 

xxplate

 film. 

 

2)  If necessary, press the 

HEATER

 button to turn the heater on.  

 
3)  Allow sufficient time for the unit to reach temperature (the 

Heater

 

LED will stop flashing and remain constantly on). 

 

4)  Fit the 

BJS xxplate Adapter Block

 into the 

PCR 96 Well Skirted 

Plate

 

Adapter Block

 (both provided with the 

xxsealer

) and locate 

in the 

Adapter Block Carrier

 

 

 

 

 
5)  Load the 

xxplate

 onto the 

xxplate Adapter Block

 locating it onto 

the sprung pins. It should sit flat on the adapter block.  
And add the sealing film on top, the correct way up.  
 

 

WARNING 

Care should be taken not to touch 

the surface of the heater plate whilst 

loading the sample plate. 
 

 

XXSEALER USER MANUAL - 1.0 

 

 

 

Summary of Contents for xxsealer



























Reviews:

No comments