background image

 8

For maximum performance from your BISSELL ProLite Vacuum, it 
is recommended you perform these simple maintenance checks.

The Dust Bag should be checked weekly. It should be replaced 
when it is near full or when cleaning suction diminishes. 

Never 

reuse a Vacuum Bag

.

Unplug vacuum.

Unzip Cloth Bag. Remove Collar Retainer by pressing 
on the two tabs and then pull the top towards you. 
Slide Dust Bag collar up and out of retainer. Dispose 
of Dust Bag.

Slide collar of new Dust Bag completely into Collar Retainer.

Push Collar Retainer back into position and secure 
in place.

Tuck the remainder of the Dust Bag completely inside 
the Cloth Bag. Make sure it lays flat, top to bottom, 
without bunching. Zip Cloth Bag.

Replacement Bag: BISSELL Style 6 Filtrete HEPA 
Bags (#32052) or Micro Filtration Bags (#32062)

The ProLite features a wide diameter Dust Tube designed to 
optimize cleaning power. For best performance it should be 
routinely checked and cleared of excess dust and other debris.

Note: It is recommended the tube be cleaned on 
a bare floor, or with some newspaper to cover 
the floor, to catch any loose material or dust 
removed during cleaning. 

Release Bag Tension Spring behind the bottom of 
Cloth Bag.

Using a screwdriver, unscrew filter cover. Unplug 
Connector Plug.

Locate the Tube Release Button at the top of the Powerfoot. 
The button is hidden under a rubber collar and may be 
covered with a piece of tape. The button can be pressed 
through the tape to release the tube. Lift off the tube while 
pressing on the Tube Release Button.

Use a wire brush to clean out the inside of the tube and 
the top section of the Powerfoot where the tube connects.

1.

2.

3.

4.

 WARNING: 

To 

reduce the risk of electric 
shock, turn Power Switch 
OFF and disconnect 
polarized plug from 
electrical outlet before 
performing maintenance or 
troubleshooting checks.

Replacing the Dust Bag

1.

2.

3.

4.

Routine Maintenance

5.

Tip:

Vacuum new carpet 
or vacuuming fine 
powders may clog 
the Dust Bag. So 
check the bag 
more often.

Cleaning the Dust Tube

Tube 
Release 
Button

Rubber 
Collar

Tube 
Release 
Button

Clean

Filter 
Cover

ug310-6004_3561_404.indd   8

ug310-6004_3561_404.indd   8

4/29/04   8:29:08 AM

4/29/04   8:29:08 AM

Summary of Contents for ProLite 3561 SERIES













Reviews: