background image

SmartMix

®

Provides custom control for each cleaning job.
1. Lift the SmartMix

®

concentrate bottle up out of the 

machine base.

2. Flip the bottle over so that the valve cap is in an 

upward position.

3. Unscrew the valve cap and fill the bottle to the mark with

BISSELL cleaning solution.

4. Replace the valve cap turning until snug.
5. Replace SmartMix

®

concentrate bottle.

6. Choose the SmartMix

®

setting that fits the cleaning job.

Water Only

– use for gentle cleaning or for the final

rinse after cleaning.

Normal

– automatically provides the best mix of 

water and concentrate for most cleaning jobs.

High Traffic

– automatically mixes the right amounts

of water and concentrate to dissolve tough grime and
heavy soil.

6

SmartMix

®

Bottle

SmartMix

®

Switch

HIGH

TRAFFIC

W

ATER

ONL

Y

NORMAL

When filling bottle or 
storing unit, set

dial to: 

Tip:

Deep cleaning

stairs and high
traffic areas on 
a regular basis
can prolong 
carpet life.

The Basics - continued

WARNING:

Be extra careful when 

cleaning stairs.

HIGH

TRAFFIC

NORMAL

WA

TER

ONL

Y

Summary of Contents for PROHEAT PLUS 1698 POWERSTEAMER


















Reviews: