A
Product View
C1 - Rewind
Your vacuum is equipped with an automatic
cord rewind. When cleaning is finished, press
the power button OFF and grasp the plug
to disconnect from the electrical outlet. Hold
the plug and press the automatic cord rewind
button to rewind the cord automatically.
C2 - Power button
Turn the power ON or OFF by pressing lightly
downward on the power button ( ).
Special tools
Your BISSELL vacuum is not only a powerful
carpet and rug vacuum cleaner, it’s also a
versatile bare floor and above floor vacuum
cleaner when you select one of the special
tools.
Floor nozzle (12)
Use to vacuum carpets, rugs and bare floors.
Swivel head turns to get into tight spaces
and fits under cabinets.
1.
To vacuum carpets and rugs, push the brush
switch to the carpet position
. This will
pull the brushes up into the floor nozzle.
2.
To vacuum bare floors, push the brush
switch to the bare floor position
. This
will extend the brushes down from the floor
nozzle.
Small accessories (13)
Use the crevice tool in tight, narrow spaces.
Use the dusting brush to clean curtains,
draperies, and side tables and window
ledges. Use upholstery tool for soft
furnishings.
TurboBrush™ Tool (14)
(select models only)
Use rotating brush action for small, flat areas
such as cushions and beds.
NOTE: Press down gently and pull toward
you in a raking motion. Too much pressure
will cause the brush to stop rotating.
Hard Floor Brush (15)
(select models only)
Specially designed to vacuum bare floors.
Turbine Head (16)
(select models only)
Use to vacuum carpets and rugs. Swivel
head turns to get into tight spaces and fits
under tight cabinets. Easy-to-remove nozzle
window for cleaning threads and debris from
the brush roll. Squeeze the 2 small tabs at
the side of the foot to release the window.
To replace, align the window tabs at the top
with the 2 openings of the foot and push
into place until you hear a snap and the
window is securely in place.
B
Assembly
1.
Connect hose to vacuum by inserting hose
connector on the end of the hose into the
suction inlet. Make sure the hose is positioned
so the tabs on the hose connector line up
with the notches on the suction inlet.
2.
Connect hose handle to the end of the
extention wand and twist slightly to tighten.
3.
Connect floor nozzle to the end of the
extension wand and twist slightly to tighten.
4.
Once assembled, you can store your
vacuum by inserting the storage clip
(located on the back of the floor nozzle) into
the storage slot on the rear of the vacuum.
Colours may vary from models shown.
C
Operations
Power cord
The power cord is located at the rear of the
vacuum. Gently pull out the power cord,
watching for the yellow line. Stop pulling the
power cord once the yellow line is visible.
There is also a red line, which indicates
the end of the usable cord. Do not pull the
power cord out beyond the red line.
Do not plug in your cleaner until you have
completely assembled it per the following
instructions and are familiar with all instructions
and operating procedures.
Be careful to avoid injury as cord retracts very quickly.
Plastic film can be dangerous. To avoid danger of
suffocation, keep away from babies and children.
Before using your vacuum, make sure that the dirt
cup and all filters are in place. Do not operate your
vacuum without the dirt cup and filters.
1 Handle
2 Air Flow Regulator
3 Extension Wand
4 Hose
5 Carry Handle
6 Dirt Cup Release Button
7 Dirt Cup Lid Release Button
8 Cyclone
9 Easy Empty™ Dirt Cup
10 Hose Connector
11 Brush Switch
12 Multi-Surface Floor Nozzle
a. Up / b. Down
13 Crevice Tool, Dusting Brush &
Upholstery Tool w/Holster
14 TurboBrush™ Tool*
15 Hard Floor Brush*
16 Turbine Nozzle*
* Not all parts are included with every model.
5
www.bissell.ca
1-800-263-2535
