Biotek PowerWave Operator'S Manual Download Page 135

Page: 135 / 176

Appendix A

D e c o n t a m i n a t i o n

This appendix contains the procedure for decontaminating

the PowerWave.

Decontamination Procedure

If the PowerWave is to be shipped after being exposed to potentially

hazardous material, it should be decontaminated. The following

procedure outlines how to decontaminate the instrument before

packaging and shipment.

Purpose

Decontamination minimizes the risk to all who come in contact with the

reader during shipping, handling, and servicing. It is also required by the

U.S. Department of Transportation regulations.

General Considerations

Any laboratory instrument which has been used for clinical analysis is

considered a biohazard and should be decontaminated prior to handling.

Intact skin is generally considered an effective barrier against infectious

organisms; however, small abrasions and cuts may not be always be

visible. Prophylactic gloves must be worn when handling instruments

that have not been decontaminated. Gloved hands should be considered

contaminated at all times and must be kept away from eyes, mouth and

nose at all times.

Mucous membranes are considered prime entry routes for infectious

agents. Wear eye protection and a surgical mask when there is a

possibility of aerosols.

Eating and drinking while decontaminating instruments is not advisable.

Summary of Contents for PowerWave
















































































































































































Search results

Summary of Contents for PowerWave

Reviews:

Biotek PowerWave, Operator'S Manual, Page: 135 / 176

Search results

Summary of Contents for PowerWave

Reviews: