background image

6

1. Assembling the humidifier on the rod or ventilator.(pic 1)

2. Place the chamber on the heating plate then push the chamber all the way into the slot.

     The chamber protection rod will raise to fix the chamber.(pic 2)

3. Add distilled water into the chamber to the full fill line.(pic 3)

4. Connect the ventilator air way into chamber inlet .(pic 4) This device is intended to be 

    used with 22 mm corrugated ventilator tubing with a minimum length of 24 inches between 

    the reservoir and the patient connection.

5. Connect the patient end air way to the chamber outlet side.

6. Strongly recommend add a small temperature in the patient side to monitor the temperature.

7. Connect the air way between patient and ventilator segment.

8. Now the humidifier is ready to use.

                

               Caution

     

 Do not fill the chamber above the maximum level. Liquid could enter the breathing 

          circuit if the chamber is overfilled. 

     

 Do not install the humidifier above the patient level.

     

 Failure to use the minimum length of tubing specified may result in unsafe temperatures

           delivered to the patient

5  

     Assembling

(1)

(2)

(4)

(3)

Summary of Contents for EverHeart EH-01














Reviews: