background image

Quest 215 Dual

Quest Dry

Quest 506

Installation, Operation and Maintenance Instructions

This manual is provided to acquaint you with the 

dehumidifier so that installation, operation and 

maintenance can proceed successfully. Ultimate 

satisfaction depends on the quality of installation and a 

thorough understanding of this equipment. The dehumidifier 

is built around tested engineering principles and has passed 

a thorough inspection for quality of workmanship and 

function.

Installation, Operation and Maintenance Instructions

4201 Lien Rd 

Madison, WI 53704 

Toll-Free 1-877-420-1330

www.QuestHydro.com [email protected] 

– Read and Save These Instructions –

Specifications subject to change without notice.

1

Features:
•  Industry-leading efficiency, most efficient on the market 

today

•  Patented, refrigeration system
•  High-efficiency, long-life impeller fan
•  Quiet operation
•  Superior air filtration (MERV-13 standard)
•  Auto-restart after power outages
•  Environmentally friendly R410A refrigerant
•  Low voltage control

TS-1016

10/17 Rev. A

Water Removal Rates (Pints/Day) @ 80°F 60% (AHAM)

 

 

Dehumidifier 

Pints Removed  Gallons/Liters

 

Quest 506 

506 

63.2/239.4

PATENT PENDING

Summary of Contents for 506













Reviews: