manualshive.com logo in svg

BIO-MED DEVICES 2005IC, Instruction Manual, Page: 30 / 36

Share
Download
BIO-MED DEVICES 2005IC Instruction Manual Download Page 30

 

28

2.      PILOT VALVE BLEED 

With both supplies on, place your ear near back of case. An audible internal leak is 
normal. 

 
3.      PILOT VALVE SEAL 

With both supplies pressurized and ON/OFF valve to OFF, occlude the circuit 
exhalation valve exhaust port and observe the manometer on the unit.  There 
should be no continuous rise in pressure indicated by manometer. 

 

4.      MANOMETER 

Using a variable low-pressure source and known standard, verify 3% full-scale 
accuracy and a zero of +/- 1 cm. 

 

5.     RELIEF VALVE 

CAUTION:

 Proceed with care. If the relief valve is malfunctioning, damage to the 

manometer may occur during this check. 
 

NOTE:

 The point at which the relief valve begins to fully open may cause oscillation 

in the manometer. This is normal. 
 

Set Flow Rate to minimum flow. Set ON/OFF switch to ON. Occlude circuit 
exhalation valve exhaust port and observe manometer.  Slowly increase the flow 
rate to 20 LPM.  A minimum of 100 cm of pressure should be indicated during 
inspiratory. Continue to slowly increase flow to 75 LPM. The pressure during 
inspiratory should not be less than 100 cm or greater than 130 cm. 

 
6.     MAXIMUM PRESSURE 

Set INSPIRATORY TIME to 2 sec.  Set ON/OFF switch to ON.  Observe the 
manometer while increasing the flow rate through its entire range. The circuit 
pressure during inspiratory must be 100 cm or greater through entire flow range. 

 

7.     MAXIMUM PRESSURE ZERO 

Turn Maximum Pressure knob fully CW. Set ON/OFF switch to ON.  Observe the 
manometer. Except at start of inspiratory, no more than 1 cm rise in pressure 
should be observed. 

 
8.     FAILSAFE 

Set ON/OFF switch to ON.  Manometer should indicate Maximum Pressure during 
Inspiratory.  Slowly decrease the logic supply pressure. At a supply pressure of 30 
PSI or less, the patient circuit should stop pressurizing while the unit continues to 
cycle. 

 

9.     PEEP PRESSURE 

Turn PEEP knob fully CCW and install test lung at patient end of circuit. Set 
ON/OFF switch to ON. The test lung should fill by the second breath and the 
manometer should indicate a PEEP pressure of 25 cm ±3. Switch 
CYCLE/MANUAL CPAP switch to MANUAL CPAP. Unit will continue cycling 
without inspiratory pressurization and with no CYCLE INDICATOR action. PEEP 
pressure should be 25 cm ±3. Press and release the Manual Button.  A 
pressurized bolus of gas will be delivered. 

Summary of Contents for 2005IC





































Reviews:

No comments