background image

CNCR-190 • Two-wire 4-20 mA/HART  

16

Code

Text message

Cause

Rectification

DevSpec

State in 

CMD 48

M500

Error in the delivery status

Bit 0 of

Byte 14 to 24

M501

Error in the delivery status

Bit 1 of

Byte 14 to 24

M504

Error at a device interface

Hardware defect

Check connections 

Exchanging the electronics

Send instrument for repair

Bit 4 of

Byte 14 to 24

M505

No echo available

Sensor does not detect an 

echo during operation

Antenna dirty or defective

Clean the antenna

Use a more suitable antenna/sensor  

Remove possible false echoes

Optimize sensor position and 

orientation

Bit 5 of

Byte 14 to 24

M507

Error in the instrument 

settings

Error during setup

Error when carrying out a reset 

False signal suppression faulty

Carry out reset and repeat setup

Bit 7 of

Byte 14 to 24

M508

Data error in program  

memory Bluetooth controller

Bit 8 of

Byte 14 to 24

M509

Software update

Bit 9 of

Byte 14 to 24

M510

No communication with

the sensor

Bit 10 of

Byte 14 to 24

Maintenance

10  Certificates and approvals

10.1 Radio licenses

Radar

The device has been tested and approved in accordance with the current edition of the applicable 

country-specific norms or standards.

Bluetooth

The Bluetooth radio module in the device has been tested and approved according to the current edition  

of the applicable country-specific norms or standards.

9  Removal

9.1 Disposal

The device is made of recyclable materials that can be disposed of by specialty recycling companies. 

Observe the applicable local regulations for proper disposal.

Summary of Contents for CNCR-190





















Reviews: