background image

2

www.bindicator.com

LAR180212 Rev. E

II. GENERAL SAFETY

AUTHORIZED PERSONNEL

All instructions described in the document must be performed by authorized and qualified service personnel 

only. Before installing the unit, please read these instructions and familiarize yourself with the requirements and 
functions of the device. The required personal protective equipment must always be worn when servicing this 
device.

USE

The device is solely intended for use as described in this manual. Reliable operation is ensured only if the 

instrument is used according to the specifications described in this document. For safety and warranty reasons, 
use of accessory equipment not recommended by the manufacturer or modification of this device is explicitly 
forbidden. All servicing of this equipment must be performed by qualified service personnel only. This device 

should be mounted in locations where it will not be subject to tampering by unauthorized personnel.

MISUSE

Improper use or installation of this device may cause the following:

•   Personal injury or harm
•   Application specific hazards such as vessel overfill
•   Damage to the device or system

If any questions or problems arise during installation of this equipment, please contact the manufacturer 
Customer Support at 800-778-9242.

WARNING: ONLY CERTAIN MODELS CAN BE USED IN HAZARDOUS LOCATIONS; SEE NAMEPLATE. 
THESE MODELS SHALL ONLY BE USED IN APPLICATIONS COVERED BY THE STATED RATINGS OR 
NON-HAZARDOUS LOCATIONS.

StockCheck.com

Summary of Contents for Roto-Bin-Dicator

















Reviews: